Extron-electronics TPX 88 Series User Manual

Browse online or download User Manual for Audio accessories Extron-electronics TPX 88 Series. Extron Electronics TPX 88 Series User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 1
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
This sheet provides quick start instructions for an experienced installer
to set up and operate the TPX 88 Series matrix switcher.
About Audio
The TPX 88 A has local audio outputs on 5-pole,
3.5 mm captive screw connectors. These outputs
always follow the RJ-45 outputs, regardless of
whether the audio follows the video or is broken
away from the video in the TP ties.
N The TP transmitters and receivers distribute audio in a proprietary digital channel of
the TP link.
• TheTPX88cannot switch this audio.
• TheTPX88Acan switch this audio and extract it for the local audio connectors.
N The audio distributed by MTP transmitter and receivers is incompatible with the
audioextractionandprocessingcapabilitiesoftheTPX88A.
• TheTPX88andtheTPX88Acannot switch the mono audio that is distributed
by most MTP transmitters and receivers.
• TheTPX88andtheTPX88Acan switch the stereo audio that is distributed by
stereo audio versions of the MTP S-video and composite video transmitters and
receivers, but the TPX88A cannot extract it for the local connectors.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP switcher as
required.
Step 2 — TP inputs and outputs
Terminate up to eight
TP input cable and up to
eight TP output cables as
shown at right. Connect
them between the TPX 88
and the TP input and output devices.
N TheTPX88doesnotsupportthe
remote power capability of some TP
transmitters and receivers.
Step 3 — Connect a local audio
device (TPX 88 A)
Connect up to eight audio devices to the
Audio Outputs connectors. Wire the
connectors as shown below.
C Connect the sleeves to ground
(Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio
output circuits.
Setup Guide — TPX 88 Series
Unbalanced Stereo Output Balanced Stereo Output
L R
Do not tin the wires!
Ring
Sleeve(s)
Tip
Tip
Ring
Sleeve(s)
Tip
Tip
NO GROUND HERE.
NO GROUND HERE.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Setup Guide — TPX 88 series (cont’d)
68-733-50
Rev. A 02 09
Typical TPX 88 application
Step 4 — Remote connector
• Connectaserialportcontroller.Wirethe
connector as shown in the table at right.
• UsetheRS-232/RS-422DIPswitchesto
configure the port for the desired protocol.
Step 5 — Power
PlugastandardIECpowercordbetweenthe
powerconnectoranda100VACto240VAC,50
or 60 Hz power source.
Operation — Creating ties
A Tie is an input-to-output connection. An input can be tied to more than one outputs. An
output can never be tied to more than one input.
Create ties as follows:
1. TPX 88 A only —PressandreleasetheI/O
button to select video and audio, video only,
or audio only.
2. Press and release the desired input button.
3. Press and release the desired output button(s).
4. PressandreleasetheEnterbutton.
1 2
3
4
5
6
7 8
AUDIO
OUTPUTS
INPUTS
1
2
3
4 5
6 7 8
OUTPUTS
OUTPUTS
REMOTE
L
R
1
L
R
2
L R
3
L
R
4
L R
5
L
R
6
L
R
7
L R
8
RS-232
RS-422
GND
TX-
TX +
RX -
RX +
0
1
TP T 15HD A
H-SHIFT
BUFFERED
COMPUTER
INPUT
AUDIO
ID PIN 4
ID PIN 11
LOCAL MONITOR
TP T 15HD A
H-SHIFT
BUFFERED
COMPUTER
INPUT
AUDIO
ID PIN 4
ID PIN 11
LOCAL MONITOR
PC
VIDEO INPUT
VTT001CM
Twisted Pair Receiver
POWER
VIDEO INPUT
VTT001CM
Twisted Pair Re
ceiver
POWER
C SYNC
SOG
C VIDEO
N/C
L R
AUDIO
OUTPUT
AV INPUT
RGB
POWER
15V
.34A MAX
C SYNC
SOG
C VIDEO
N/C
L R
AUDIO
OUTPUT
AV INPUT
RGB
POWER
15V
.34A MAX
50-60Hz
100-240V 0.3A
LISTED
1T23
I.T.E.
ANAHEIM, CA.
MADE IN USA
XPA 1002
Audio Power
Amplier
XPA 1002
1
2
LIMITER/PROTECT
SIGNAL
OVER
TEMP
Audio
TP T 15HD A
Twisted Pair
Transmitter
TPX 88 A
Twisted Pair
Matrix Switcher
TP T 15HD A
Twisted Pair
Transmitter
Macintosh
®
Computer
Control
System
VTR001
Twisted Pair
Receiver
VTR001
Twisted Pair
Receiver
Stereo
Audio
LCD Projector #2
Presenter’s
Display
Lobby
Display
TP R 15HD A
Twisted Pair Receiver
Stereo
Audio
LCD Projector #1
TP R 15HD A
Twisted Pair
Receiver
Audio
SI 28
Surface-mount
Speakers
AUDIO
OUTPUTS
LR
1
LR
2
LR
3
LR
4
LR
5
LR
6
LR
7
LR
8
1234 56 78
INPUTS
1234 56 78
OUTPUTS
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
NOTE If you are using Enhanced Skew-Free™ A/V
cable, use the TIA/EIA T568A standard only.
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
12345678
RS-232 FunctionPin
Gnd
TX+
RX+
Gnd
TX-
TX+
RX-
RX+
Signal ground
Not used
Transmit data
Not used
Receive data
Gnd
TX-
TX+
RX-
RX+
Signal ground
Transmit data (-)
Transmit data (+)
Receive data (-)
Receive data (+)
RS-422 Function
RS-422
Switches 1 & 2
down, 3 up
RS-232
All switches up
(Default)
REMOTE
RS-232
RS-422
GND
TX-
TX +
RX -
RX +
VIDEO
AUDIO
I/O
Press the button to cycle
through the selections.
Lights green when video is selected.
Lights red when audio is selected.
5
Press
3 4 8
Amber indicates video and audio tie.
Green indicates video tie.
Red indicates audio tie.
Page view 0
1

Summary of Contents

Page 1 - Setup Guide — TPX 88 Series

This sheet provides quick start instructions for an experienced installer to set up and operate the TPX 88 Series matrix switcher.About AudioThe TPX

Comments to this Manuals

No comments