Extron electronics DVS 406 User Manual download pdf

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805



USA

714.491.1500 

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort



The Netherlands

+31.33.453.4040 

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building



Singapore 368363

+65.6383.4400 

Fax +65.6383.4664

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami



Chiyoda-ku, Tokyo 102-0074 Japan 

+81.3.3511.7655 

Fax +81.3.3511.7656

www.extron.com

33-591-01 B

03 02

Printed in the USA

Installation

DVS 406

Installation, cont'd.

1. Turn off power to the DVS 406 and all other devices that will be connected.

See example application diagram below right.

2. If the scaler is to be rack or furniture mounted, position the brackets and insert

the mounting screws. For rack mounting, be sure to remove the self-adhesive

rubber feet if they have been attached. See the rack mounting diagram at right.

3. If using Input 1, attach an RGB or HD YUV pass-through signal. The HD YUV

signal will be converted to RGB on the output.

If using Input 2, attach either an RGB pass-through, RGBcvS, YUVp,

or YUVi signal.

If using Inputs 3 to 5, attach an S-video or composite video source.

If using Input 6, connect the SDI signal to the BNC.

4. Connect up to six balanced or unbalanced stereo audio input devices to the DVS 406. Each audio input has a 3.5 mm, 5-pole captive

screw connector. The illustrations below indicate how to wire the connectors for the appropriate audio input type and impedance.

5. For display output, connect an output display device to the output BNC connectors.

6. Connect an RGB display device to the 15-pin HD output connector. Using this connector and the output BNCs will allow simultaneous

output.

7. For unamplified audio output, connect an audio device to the 3.5 mm, 5-pole captive screw connector using the wiring diagram.

Connect the sleeve to ground. Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

8. Plug the DVS 406, and input and output devices into a grounded AC source, and turn on the input and output devices.

9. Use the LCD menu screens (see below) or RS-232 programming to configure the scaler.

Input configuration – Select RGB or HD YUV pass-through for Input 1, RGB pass-through, RGBcS, YUVp, or YUVi for Input 2,

S-video or composite video for Inputs 3 - 5, or SDI (serial digital interface) for Input 6.

Use the MENU and NEXT buttons to navigate through the menu system. Use the Adjust knobs to make configuration changes.

Output configuration – Select the required output resolution and refresh rate combination. Select the display's sync format:

RGBHV, RGsB, or RGBS. Select positive or negative sync polarity for the horizontal and vertical sync.

Audio configuration – To create a smoother transition when switching from one audio input to another, the audio levels can be

adjusted from -15dB to +9dB. Also, the timing for switching to a different audio input can be adjusted: Start (switches to the next

audio at the beginning of the next video input), Middle (switches to the next audio halfway into the next video input), End

(switches to the next audio at the end of the next video input), or Fade (gradually mutes the current audio halfway between the

switch to the new video input, then gradually increases the next audio input from mute).

Memory Presets – The presets save Sizing, Centering, and Blanking information for each input (up to 3 presets per input)

except for the pass-through inputs (Input 1 and RGB on Input 2). Select a preset number in the Save submenu of the input,

then press the NEXT button to save it, or delete a saved preset in the Clear submenu of the input by selecting it, then press the

NEXT button to clear the preset.

To recall an input's saved preset, select the input and press the input button successive times to activate each saved preset for

that input. Each recalled preset will display the message "Input #X Memory Y" where "X" refers to the input (2 to 6) and "Y"

refers to the preset (1 to 3).

Advanced Configuration – When selecting the Effect type to transition from Input 1 and another input, a cut will cause an

immediate switch, while a dissolve will cause a gradual fade out and fade in (.2 to 1.0 sec). The Take button initiates the switch.

The Edge smoothing feature can be set On/Off. Edge smoothing softens the edges of a picture by minimizing pixel differences.

The Top and Bottom blanking feature is used to remove noise and other undesired extraneous material, such as closed

captioning, by removing scan lines from the top or bottom of the screen. Up to 127 lines can be removed.

RGB delay allows for glitchless switching between video inputs by switching to the new sync signal before switching to the new

video signal. The video signal delay can be adjusted from 0 to 5 seconds in 0.5 second steps.

The Switch mode feature enables input switching automatically (Auto) when a new input is selected, or only after the Take

button is pressed (Take).

Blue mode can be set On/Off. Setting this mode On will pass only sync and blue signals to the display for setup purposes.

Key mode allows Input 1 and any other input to be displayed simultaneously, one over the other. Key mode must be set On and

the other input must have it's output resolution locked to Input 1. With the second input selected, press the Take button

(Switch mode previously set to "Take"), then press Input 1 twice to initiate the Key mode effect. Press any input button to escape.

Enhanced mode can be set On/Off. Setting this mode On will activate signal gain for increased image sharpness.

Reset will reset the scaler to its factory default values. Press the Take button for about 2 seconds until the LCD confirm prompt

message appears, then press the Take button again.

Exit – Return to the default menu cycle by pressing the NEXT button or return to the main menu system by pressing MENU.

NOTE

RGsB

HDTV Component

RGBHV

RGBS

HD YUV to / RGB PASS THROUGH

R G B V

HD YUV to / RGB PASS THROUGH

R G B

/HV

HD YUV to / RGB PASS THROUGH

R G B V

HD YUV to / RGB PASS THROUGH

R G B V

Codec

DVD

Extron

DVS 406

2A MAX

100-240V 50-60Hz

RS-232

SDI

RGB/R-Y

B-Y

S-VIDEO

VIDEO

1 - RGB P

ASS

THR

OUGH

H/V

Video Camera 1

Video Camera 2

RS-232

Control

Projector

VCR

Plasma

Display

Extron

RGB 109xi

Example application

PICTURE ADJUSTMENTS

DIGITAL VIDEO SCALER

VIDEO/

S-VIDEO

RGB/YUV

RGB

VIDEO/

S-VIDEO

VIDEO/

S-VIDEO

SDI

TAKE

COL/TNT

BRT/CONT

DETAIL

SIZE

CENTER

DVS 406

ADJUST

Rack mounting

RGsB

Component

(R-Y, Y, B-Y)

RGBHV

RGBS/RGBcS

G B

/HV

2 - RGB PASS THROUGH / R-Y, B-Y, Y

/R-Y

/B-Y

G B

/HV

/R-Y

/B-Y

G B

/HV

/R-Y

/B-Y

/R-Y

/B-Y

2 - RGB PASS THROUGH / R-Y, B-Y, Y

S-video

/VID

Composite video

/VID

SDI

L R

AUDIO

L R

AUDIO

L R

AUDIO

Unbalanced Input

Tip

Sleeve

Tip

Sleeve

Balanced Input

Tip

Ring

Sleeve (s)

Tip

Ring

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Input

(high impedance)

(high impedance) (600 ohms)

600 ohms

RGBSRGBHV RGsB (Sync on Green)

R G B

H/HV

V R G B

H/HV

V R G B

H/HV

Unbalanced Output

Tip

See Warning

Sleeve (s)

Tip

See Warning

Balanced Output

Tip

Ring

Sleeve (s)

Tip

Ring

L R

AUDIO

L R

Main Menu System

Power



Extron

DVS 406

Input

Configuration

2 sec.

Input #2

RGB

Output

Configuration

Audio

Configuration

Memory

Presets

Advanced

Configuration

Exit

2A MAX

100-240V 50-60Hz

RS-232

RGB

2 - RGB PASS THROUGH / R-Y, B-Y, Y

1 - RGB PASS THROUGH

SDI

5 643

R G B H/HV V

/RY

/B-Y

R G B V

V C

/HV

/VID

/HV

1L R

INPUTS

OUTPUT

2L R 3L R 4L R

L R

5L R 6L R

DVS 406

RGB 109xi

RS-232

Control

DVD Player

Codec

VCR

Projector

Plasma Display

Video Camera 1

Video Camera 2

RGB 109xi

BUFFERED LOCAL

MONITOR OUTPUT

H. SHIFT

INPUT

VGA INTERFACE W/ADSP

ID PIN 4

ID PIN 11

PC Computer

Application Example

/R-Y

/B-Y

/HV

/R-Y

/B-Y

/HV

/R-Y

/B-Y

/R-Y

/B-Y

/HV

Summary of Contents

Page 1 - Main Menu System

Extron Electronics, USA1230 South Lewis StreetAnaheim, CA 92805USA714.491.1500 Fax 714.491.1517Extron Electronics, EuropeBeeldschermweg 6C3821 A

Extron electronics DVS 406 User Manual

Browse online or download User Manual for DVD players Extron electronics DVS 406. DVS 406 label_ rev B.eps

Summary of Contents

More documents for DVD players Extron electronics DVS 406

Comments to this Manuals

Extron electronics DVS 406 User Manual

Browse online or download User Manual for DVD players Extron electronics DVS 406. DVS 406 label_ rev B.eps

Summary of Contents

More documents for DVD players Extron electronics DVS 406

Comments to this Manuals

Related products and manuals for DVD players Extron electronics DVS 406