VoiceLift™ MicrophoneInstallation Guide for VLM 1000 and VLM 200068-1629-01 Rev. A01 09
VoiceLift Microphone Installation • Installation — Overview2-2Installation — Overview, cont’dOutline of installation stepsStage 1 — Install the VLR 10
Installation — Stage 1Receiver housing and back plateWhere it goes: The housing attaches to the receiver dome, and the back plate mounts to a ceilin
1. Cut a hole in the ceiling tile.a. Remove the ceiling tile in which the receiver will be installed.b. Determine the hole location, then cut a hole
3. Attach a conduit to the back plate if needed.If desired, attach a conduit to the open knockout in the back plate.N Observealllocalandnational
1. Install the junction box.Install the junction or ceiling box (not included) flush to the surface. Use a one-gang plaster ring (Raco 772) if the ju
Installing the Receiver in a Wall or Other Hard Surface1. Install a raceway if needed.If using a raceway for the cables, install it at the appropriate
4. Mount the receiver housing to the surface.If not using a raceway: Mount the receiver housing and base to the surface, using the appropriate screws
Stage 2This stage consists of installing/connecting the items shown below.Ethernet cableCAT 5, 5E, or 6 with T568A or T568B straight through wiring Wh
Ä Pull the cable(s). 1. Pull the cables to the receiver. a. Pull the communication/power Ethernet cable through the receiver’s base, along with any
ON12CTS-2ON1 2CTS-2MIXTONERS-232AUX INCTC+OUTINRLYTxINRxCNOMIXTONEBase PlateÖ Locate the arrow on the housing rim.Ñ Locate the locking tab marked wi
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipmen
3. Attach the receiver dome to the housing (continued).c. Place the dome onto the housing, aligning the arrow on the dome’s locking tab with the arro
4. Pull cables to the PoleVault switcher.a. Pull the cables from the receiver to the PoleVault switcher’s location.b. Remove the base of the PMK Pol
Stage 31. Congure the system.Follow the steps in your PoleVault installation guide to congure the PoleVault system.2. Set up the microphone.(Refer t
3. Test the system (continued).c. Use a screwdriver to adjust the audio to the proper level by rotating the Aux/Mix encoder on the PoleVault switcher
1. Connect the receiver to the MLC 104 IP Plus.a. Wire one of the provided two-pole captive screw connectors to one end of a communication cable.b.
2. Congure the MLC 104 IP Plus.a. Using Global Congurator, congure the MLC’s Digital I/O port for digital input with pull-up.b. Configure a monito
VoiceLift Microphone Installation • Reference Information2-18Reference InformationAudioTone control ... On or off, s
2-19VoiceLift Microphone Installation • Reference Information GeneralPower ... 12 VDC supplied by an Extro
VoiceLift Microphone Installation • Reference Information2-20Installation — Reference Information, cont’dAudio/acoustic and electricalMicrophone type
2-21VoiceLift Microphone Installation • Reference Information Specications — VLC 102 Microphone Charging StationGeneralExternal power supply ...
VoiceLift Microphone Installation • Introduction — Overview1-1Introduction — Overview About This GuideThis manual covers the installation of the Extro
© 2009 Extron Electronics. All rights reserved.Extron USA - West Headquarters+800.633.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAXE
VoiceLift Microphone Installation • Introduction — PlanningIntroduction — Planning1-2Before You Begin — Planning the InstallationBefore starting insta
VoiceLift Microphone Installation • Introduction — Planning 1-3Room considerationsRoom factors to be considered should include, but are not confined to
VoiceLift Microphone Installation • Introduction — Planning1-4Introduction — Planning, cont’d• Optional VLR 102SR Secondary receiver. One or more se
1-5VoiceLift Microphone Installation • Introduction — Inventory Overview Introduction — Inventory OverviewVLP 102Pendant MicrophoneVLP 102 Pendant Mic
1-6Introduction — Inventory Overview, cont’dVoiceLift Microphone Installation • Introduction — Inventory Overviewb. Items not includedThe following i
N For operation and setup of other Extron PoleVault system components mentioned in this guide, refer to the appropriate user manual provided wit
Comments to this Manuals