DVS 100 and DVS150Digital Video Scalers 68-459-01Printed in USA
Introduction, cont’dDVS 100 and DVS 150 Introduction1-4
2DVS 100 and DVS 150Chapter TwoInstallationRear Panel FeaturesInstallationFront Panel FeaturesConfiguring the Scaler
Installation, cont’dDVS 100 and DVS 150 Installation2-2Rear Panel FeaturesFigure 1 — DVS 100 rear panelFigure 2 — DVS 150 rear panel1AC power connecto
2-3DVS 100 and DVS 150 InstallationInstallationOverviewTo install and set up the DVS 100 or DVS 150, follow these basic steps:1If desired, mount the s
Installation, cont’dDVS 100 and DVS 150 Installation2-4Rubber FeetBottom Side (4 Plcs) RATEV SHIFTH SHIFTCONTRASTBRITTINTCOLOR123DVS 100DIGITAL VIDEO
2-5DVS 100 and DVS 150 InstallationCablingThe scaler can connect to input devices that produce composite video,S-video, or component video, and to out
Installation, cont’dDVS 100 and DVS 150 Installation2-6If you cable the scaler for sync on green (RGsB or SOG) output,you must also configure the scal
2-7DVS 100 and DVS 150 Installation7Contrast control button — Allows you to adjust the imagecontrast. For more information, see “Adjusting an image”
Installation, cont’dDVS 100 and DVS 150 Installation2-8Vertical sync polarity (V-SYNC) — Changes the polarity of the verticalsync signal to allow any
3DVS 100 and DVS 150Chapter ThreeOperationFront Panel Operations
This symbol is intended to alert the user of important operating and maintenance(servicing) instructions in the literature provided with the equipment
Operation, cont’dDVS 100 and DVS 150 Operation3-2OperationFront Panel OperationsThe front panel includes an LCD screen that displays the current statu
3-3DVS 100 and DVS 150 Operationpress the same button again or if you stop turning the knob foreight seconds.If an image control reaches its minimum,
Operation, cont’dDVS 100 and DVS 150 Operation3-4Freeze modeFreeze mode locks the output display to the current image. Freeze modecan be activated on
3-5DVS 100 and DVS 150 OperationSystem resetTo perform a system reset, press and hold the input selection buttonwhile attaching the AC power cord. Th
Operation, cont’dDVS 100 and DVS 150 Operation3-6
4DVS 100 and DVS 150Chapter FourSerial CommunicationRS-232 Programmer’s GuideRemote Contact Closure OperationControl Software for Windows
Serial Communication, cont’dDVS 100 and DVS 150 Serial Communication4-2Serial CommunicationRS-232Control CableRS-232Control CableDVS 100DVS 150Compute
4-3DVS 100 and DVS 150 Serial CommunicationRS-232 Programmer’s GuideDVS initiated messagesWhen a local event occurs, such as a front panel operation,
Serial Communication, cont’dDVS 100 and DVS 150 Serial Communication4-4Command/response tableSymbol definitions: = CR/LF, • = space = Inputs = 1 = C
4-5DVS 100 and DVS 150 Serial CommunicationCOMMAND ASCII RESPONSE DESCRIPTIONVertical shiftSpecific value / Vph Selects vertical shift Increment u
Quick Start — DVS 100 and DVS 150InstallationStep 1Install the four rubber feet on thebottom of the scaler (1A), or mount thescaler in a rack (1B).Ste
Serial Communication, cont’dDVS 100 and DVS 150 Serial Communication4-6Using the software1. To run the Signal Enhancement Products Control Program, do
5DVS 100 and DVS 150Chapter FiveTroubleshootingOperating Problems
Troubleshooting, cont’dDVS 100 and DVS 150 Troubleshooting5-2This section gives recommendations on what to do if you have problemsoperating the DVS 10
5-3DVS 100 and DVS 150 TroubleshootingProblem Cause SolutionPicture controls Input 4 is selected Switch to input 1–3. Input 4 isare not active. (DVS
Troubleshooting, cont’dDVS 100 and DVS 150 Troubleshooting5-4
ADVS 100 and DVS 150Appendix ASpecifications
A-2DVS 100 and DVS 150 SpecificationsSpecificationsVideo inputNumber/type ... 1 composite video, 1 S-video, 1 component
BDVS 100 and DVS 150Appendix BReference InformationPart NumbersGlossary
Reference Information, cont’dDVS 100 and DVS 150 Reference InformationB-2Reference InformationPart NumbersDVS 100 and DVS 150 part numbersExtron Part
B-3DVS 100 and DVS 150 Reference InformationPre-cut cablesBNC-4 HR cable is used for RGBS cable runs, and BNC-5 is used forRGBHV cable runs. Either t
Quick Start — DVS 100 and DVS 150, cont’dConfiguring the ScalerConfiguring the scaler: Press the input and rate buttons simultaneously, and hold them
Reference Information, cont’dDVS 100 and DVS 150 Reference InformationB-4Scaling — Changes the size of an image without changing its shape.Scaling can
FCC Class B NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules
EXTRON ELECTRONICS/RGB SYSTEMS, INC.1230 South Lewis Street, Anaheim, CA 92805800.633.9876 714.491.1500 FAX 714.491.1517U.S.A.EXTRON ELECTRONICS,
1-iDVS 100 and DVS 150 Table of ContentsChapter 1 • Introduction ...
Table of Contents, cont’dii DVS 100 and DVS 150 Table of ContentsChapter 5 • Troubleshooting ...
1DVS 100 and DVS 150Chapter OneIntroductionAbout the ScalerFeatures
Introduction, cont’dDVS 100 and DVS 150 Introduction1-2About the ScalerEach DVS 100 and DVS 150 digital video scaler allows analog videosignals (compo
1-3DVS 100 and DVS 150 Introduction• Output resolutions — Supports the following output resolutions:• 640 x 480 (VGA) at 60 or 75 Hz (Hertz)• 800 x 60
Comments to this Manuals