Extron-electronics Universal Compression Tool User Manual download pdf

Universal Compression Tool Instructions

Preparing the Cable

Terminating Extron RG59/HR and RG6/

SHR Cable with BNC connectors

Terminating Extron MHR (26 AWG) and RC

(24 AWG) Cable with BNC connectors

1. Push the compression

connector onto the cable

until the center pin is flush

with the BNC front ring.

2. Place the cable and connector

in the opened compression

tool (no adapter necessary).

3. Compress the cable

and connector together,

as shown below (closed).

1. Slide the center conductor

pin onto the center conductor.

2. Place the plastic dielectric

sleeve over the center

conductor pin.

3. Slide the compression

sleeve over the dielectric

sleeve as far as possible.

4. Place the compression

connector on the cable.

5. Place the cable and connector

in the opened compression tool

(no adapter necessary).

6. Compress the cable and

connector together, as shown

below (closed).

Compression

Connector

SHR/HR Cable

BNC Front

Ring

Center Pin

Opened

Closed

Plastic Dielectric

Sleeve

Compression

Sleeve

Compression

Connector

Center Conductor

MHR/RC Cable

1. Insert the cable into the proper sized hole in the cable

stripper and line up the cable end flush with the side of

the tool.

2. Rotate the tool several times.

Apply pressure if necessary,

but do not over cut the braids.

3. Pull the cable out of the tool

with the tool still closed.

Terminating Extron RG59/HR and RG6/SHR

Cable with F-type connectors

Terminating Extron RG59/HR and RG6/SHR

Cable with RCA connectors

1. Push the compression

connector onto the cable

until the dielectric is flush with

the inner ring of the connector.

The center pin should stand out

slightly from the front ring.

2. Select and place the correct

adapter into the compression

tool. Use the gold adapter for

gold connectors and the silver

adapter for nickel connectors.

3. Place the cable and connector

in the opened compression tool.

4. Compress the cable

and connector together,

as shown on the other

side of this card (closed).

1. Place the center pin on the

exposed conductor.

2. Push the compression connector

onto the cable and pin until the

pin protrudes past the top of the

connector by approximately 1/4”.

3. Select and place the correct

adapter into the compression tool.

Use the gold adapter for gold

connectors and the silver adapter

for nickel connectors.

4. Place the cable and connector in

the opened compression tool.

5. Compress the cable and connector

together, as shown on the other

side of this card (closed).

Compression

Connector

Center

SHR/HR Cable

Compression

Connector

SHR/HR Cable

Center Pin

Dielectric

CAUTION

Using the wrong adapter can damage the tool.

Sharp cutting blades.

Use care when removing or

replacing cutting blade cartridge.

Fold back braid.

(Do not scale from illustration.)

Outer

Insulation

Center

Conductor

Dielectric

1/4"

Apply pressure to top and

bottom of cable stripper to

cut through outer insulation.

Continued on the other side.

1 2

Summary of Contents

Page 1 - Use care when removing or

Universal Compression Tool InstructionsPreparing the CableTerminating Extron RG59/HR and RG6/SHR Cable with BNC connectorsTerminating Extron MHR (26 A

Page 2 - Product Part Numbers

68-749-01 Rev. CPrinted in the USA10 03Extron Electronics, USA1230 South Lewis StreetAnaheim, CA 92805USA714.491.1500 Fax 714.491.1517Extron Electron

Comments to this Manuals

No comments

Extron-electronics Universal Compression Tool User Manual

Browse online or download User Manual for Tools Extron-electronics Universal Compression Tool. Extron Electronics Universal Compression Tool User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Extron-electronics Universal Compression Tool