Extron electronics DTP T MK 332 Setup Guide

Browse online or download Setup Guide for Video splitters Extron electronics DTP T MK 332. Extron electronics DTP T MK 332 Setup guide User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
1
DTP T FB 332 and DTP T FB 232 • Setup Guide
This guide provides instructions for an experienced installer to install either
the Extron DTP T FB 332 or the DTP T FB 232 switching transmitter into an
Ackermann GB3 (OBO-Betterman), MK Electric CableLink Plus Modular,
MK Electric CableLink Plus
Single Pan, ElectraPlan, or PUK
oor box and to make all
connections.
The transmitters switch
between one analog video and
one digital (HDMI) video input
and, paired with a compatible
receiver, can extend the
selected signal up to
330 feet (100 m) (DTP T FB 332) or
230 feet (70 m) (DTP T FB 232).
Installation
Planning
CAUTION: Failure to check these items may result in personal injury or property damage.
ATTENTION : La non-vérication des éléments listés ci-dessous peut provoquer des blessures ou dommages matériels.
Check that the installation meets the building, electrical, and safety codes.
Mounting and Cabling
Typical Floorbox
1
2
3
Step 1 Preparing the floor box
a. Install the oor box as directed by the manufacturer.
NOTE: Run all required cables and secure them with cable clamps.
b.
Turn off or disconnect all equipment power sources.
Step 2 Installing adapters
a. Determine a position in the oor box to mount the DTP T FB unit (see the image at right).
b. Identify the applicable adapter plates for the oor box (see the table below).
c. Install adapter plates to the same pair of mounting slots (see the table below for slot
recommendations) for the same position in the oor box. Slide the top ange into the
mounting slot and rotate the adapter plate down so the bottom ange rests against the
wall of the oor box.
Floor Box Adapter Plates Positions
Highest
Mounting Slot
Additional Notes
Ackermann GB3
(OBO Betterman)
995241 (2)
995241 (2) and 995242 (1)
1 and 3
2
3rd from top
For position 2, use the provided screws to attach
the 995242 adapter plate to either 995241
adapter plate.
MK Electric CableLink Plus
Single Pan
995243 (2) 1 and 3
N
/A
Do not use position 2. Use mounting screws to
secure the adapter plates to the oor box (see
figure 3 on page 3).
MK Electric CableLink Plus Modular 995244 (2) 1, 2, and 3 3rd from top
ElectraPlan 995300 (2) 1, 2, and 3 3rd from top
PUK 995300 (2) 1, 2, and 3 3rd from top
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
CONFIG
G
RS-232 IR
Rx
Tx
Tx
Rx
HDMI IN VGA IN
DTP T FB 332
AUDIO IN
OVER DTP
RESET
HDMI
VGA
HDCP
AUTO
Top Panel
Figure 1. DTP T FB Unit features
Side (under adapter plate)
(Before installation in floor box)
Side (above adapter plate)
(After installation in floor box)
Top
A
DC power input
B
Remote RS-232
C
TP function switch
D
DTP output
E
HDMI input
F
VGA Input
G
Audio input
H
RS-232/IR Over TP output
I
Conguration (USB)
J
Reset button
K
LEDs
SIG LINK
OUT
G
REMOTE
RS-232
Rx
Tx
POWER
12V
1.0A MAX
−+
DTP
HDBT
Side Panel
Page view 0
1 2 3 4

Summary of Contents

Page 1 - Installation

1 DTP T FB 332 and DTP T FB 232 • Setup GuideThis guide provides instructions for an experienced installer to install either the Extron DTP T FB 332 o

Page 2 - If the TP switch (

2 DTP T FB 332 and DTP T FB 232 • Setup Guide (Continued)Step 3 — Make side panel connections under the adapter plates and set the TP function switchA

Page 3 - XTP T FB 202

3 MK Electric CableLink Plus Single Pan floor boxDTP T FB 332POWERDTP T FB 332REMOTERS-232-+GRxTx12VA MAXXTPOWERDTP T FB 332REMOTERS-23212VA MAX9952439

Page 4 - RS-232 Device

468-2682-50 Rev. A08 14 Extron Headquarters+800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000+1

Comments to this Manuals

No comments