Extron electronics 450 Plus User Manual download pdf

33-1106-02 C

06 07

www.extron.com

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

800.633.9876 714.491.1500

FAX 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort, The Netherlands

+800.3987.6673 +31.33.453.4040

FAX +31.33.453.4050

Extron Electronics, Japan

Kyodo Building, 16 Ichibancho

Chiyoda-ku, Tokyo 102-0082

Japan

+81.3.3511.7655 FAX +81.3.3511.7656

Extron Electronics, Asia

135 Joo Seng Rd. #04-01

PM Industrial Bldg., Singapore 368363

+800.7339.8766 +65.6383.4400

FAX +65.6383.4664

N15779

LI ST ED

1T23

I.T.E.

CrossPoint 450 Plus / MAV Plus Matrix Switchers

1. Mounting — If desired, mount the switcher(s) in a standard 19" rack.

2. Video input connections —

CrossPoint 450 Plus — Connect an RGB video source to each set

of input BNC connectors.

MAV Plus — Connect a component/HDTV, S-video, or composite

video source (depending on the switcher model) to each set of input

BNC connectors.

3. Video output connections —

CrossPoint 450 Plus — Connect an RGB video device to each set

of output BNC connectors.

MAV Plus — Connect a component/HDTV, S-video, or composite

video device (depending on the switcher model) to each set of output

BNC connectors.

NOTE Connectors are grouped by video plane. Connect the input or

output on each video plane to the corresponding connector in

the correct group or on the correct basic module enclosure

(BME). Refer to the appropriate CrossPoint 450 Plus /

MAV Plus Switcher Manual, chapter 2, “Installation”, if you are not sure.

4. Audio input and output connections (audio models) —

MAV Plus 128 AV RCA — Cable the switcher for stereo audio input

and output. Each input and output has two RCA connectors (left and

right) for unbalanced audio input and output.

All other models — Connect balanced or unbalanced audio

sources to each input 5-pole captive screw connector. Connect

balanced or unbalanced audio devices to each output connector.

See “Audio Connections”, at right, to wire the connectors.

CAUTION Incorrect audio connector wiring can damage the switcher.

5. Remote port connection — If desired, connect a remote host to the

RS-232/RS-422 port. See the drawing and table below to wire the connector.

Tie — An input-to-output connection

Set of ties — An input tied to two or more outputs

Configuration — One or more ties or sets of ties

Current configuration — The currently active configuration (also configuration 0)

Global preset — A configuration that has been stored. Up to 32 or 64 global

memory presets (depending on the model) can be stored in memory. Up to 20, 32,

or 64 preset locations (depending on the number of input and output buttons) can

be selected from the front panel to either save or retrieve a preset. When a preset

is retrieved from memory, it becomes the current configuration.

6. Ethernet connection – If desired, plug an RJ-45 connector into

the Ethernet port to connect the switcher to a LAN/WAN or directly

to a computer.

7. Remote port connection — If desired, connect a computer to the

front panel Configuration (RS-232) port. Use an optional 9-pin D to

2.5 mm mini jack TRS RS-232 cable, part #70-335-01.

8. Sync connection (MAV Plus only) – If desired, attach an

external sync timing device, such as an Extron BBG 6A, to the

external sync connectors. See the drawing at right.

9. Power — Connect an IEC AC power cord.

The Extron CrossPoint 450 Plus Series matrix switchers route RGBHV video, with

or without audio, to any combination of outputs. The MAV Plus matrix switchers

route component/HDTV video, S-video, or composite video (depending on the

model). The switchers can route multiple input/output configurations simultaneously.

Description

Definitions

Installation and Cabling

Operations

NOTE The video selection button is labeled

RGBHV on CrossPoint 450 Plus switchers

and Video on MAV Plus switchers. The

function is the same with either name.

Create tie(s)

1. Press the Esc button to clear all front panel input and output selections.

2. Audio models: Press the RGBHV/Video and/or Audio button to select

video and/or audio.

3. Press the desired input button.

4. Press the desired output button(s).

NOTE If you push a wrong button, press the Esc button and start over.

5. Press the Enter button.

View ties

1. Press the View button. Output buttons light for outputs that have no ties established.

NOTE If the audio button blinks, audio is broken away (switched separately from video).

NOTE If an output button blinks, that output is muted. To toggle mute on and off, press and hold the output button for 2 seconds.

2. Press an input button. The buttons for all tied outputs light (amber for video and audio, green for video only, and red for audio only.

3. Press an output button. The buttons for the tied input and all tied outputs light.

4. Press the View button. All input and output buttons return to their unlit state.

Save or recall a preset

NOTE Matrix sizes of 32 x 32 and smaller have 32 global memory presets. Larger

matrix sizes have 64 global memory presets. Preset memory locations are

assigned to the input buttons and (on matrix sizes of 16 x 16 and smaller)

output buttons. 20, 32, or 64 presets (depending on the total number of input

and output buttons) can be selected from the front panel.

1. The save preset operation and recall preset operation are both initiated using the

Preset button.

Save a preset — Press and hold the Preset button for 2 seconds.

Recall a preset — Press and release the Preset button.

2. Press the appropriate input button to select the desired preset number.

3. Press the Enter button. All input buttons and the Enter button go out. The current

configuration is saved to or retrieved from the selected preset location.

Adjust the input audio level and output volume (audio models)

1. Press and hold the Audio Setup (I/O) button for approximately 2 seconds.

2. Press and release the desired input button or output button.

Press an input button to adjust that input’s audio level. The output buttons display the gain or attenuation level.

Press an output button to adjust that output’s volume level. The input buttons display the volume level.

The more lit or blinking buttons, the greater the level. For the input level display, green indicates gain and red indicates attenuation.

Refer to the appropriate CrossPoint 450 Plus / MAV Plus Switcher User's Manual chapter 3, “Operation”, to read the audio displays.

3. Press and release the View ( ) and Esc ( ) buttons to decrease or increase the gain or attenuation for the selected input or the volume

for the selected output by 1 step per push of the button or press and hold to ramp the level up or down.

4. Press and release the Audio button to save changes and exit Audio mode.

Operations (Continued)

Audio Connections

On audio models, audio is input to and/or output from the switcher using

captive screw connectors.

The examples below show unbalanced and balanced methods of wiring the

captive screw audio connectors for input and output. If you are wiring a

captive screw connector from an existing unbalanced audio cable, the white

insulated wire is typically the left channel (tip) and the red insulated wire is

typically the right channel (sleeve). There is no reliable standard for

existing balanced audio cables.

CAUTION Do not connect the sleeves to either the + or

terminal.

Wiring errors or plugging the audio connectors incorrectly can

damage the audio output circuits.

RS-232 Function

All models Size: 2412

3232

Default:

RS-232,

9600, 8, N, 1

RS-422 RS-422Function

—

Gnd

—

Not used

Transmit

Receive

Not used

Ground

Not used

Function

TX+

TX–

RX+

RX–

Gnd

—

Transmit (+)

Transmit (–)

Receive (+)

Receive (–)

Ground

Not used

All other models

—

TX–

RX–

—

Gnd

—

RX+

TX+

—

Not used

Transmit (–)

Receive (–)

Not used

Ground

Not used

Receive (+)

Transmit (+)

Not used

REMOTE

SYNC

Terminate cable

or connect to

another device.

To black burst

generator

Default

IP address:

192.168.254.254

I / O

RGBHV AUDIO

Green when selected.

Off when deselected.

Red when selected.

Off when deselected.

The button lights to

indicate the selection.

3 4

ENTER

Amber indicates RGBHV/video and audio tie.

Green indicates RGBHV/video only tie.

Red indicates audio only tie.

Enter blinks to indicate the

need to confirm the change.

PRESET

Preset button blinks.

Press and hold.

Preset

2 seconds

Save a

preset

Recall a

preset

Preset button lights. Press and release.

1 2 3 4 5 6

17 18 19 20 21 22

All input buttons with assigned presets light red.

The configuration data at assigned preset

locations will be overwritten.

ENTER

The button blinks red to indicate that

this preset is selected to save or recall.

The Enter button blinks

green to indicate the need

to activate the save or recall.

17 18

1 2

Press an Output button to adjust

that output’s volume.

Input buttons display

volume.

17 18

1 2

Press an Input button to adjust

that input’s gain or attenuation.

Output buttons display

gain/attenuation.

ESC VIEW

button decreases the

input level or volume.

button increases the input

level or output volume.

Audio button

stops blinking.

17 18

1 2

All input buttons and output

buttons turn off.

Press the button.

AUDIOAUDIO

AUDIO

Audio button blinks.

Hold

2 seconds

AUDIO

VIDEO RGBHV

— or —

CrossPoint

450 Plus

MAV

Plus

ENTER

Enter button stops blinking.

17 18

1 2

All input buttons and

output buttons go out.

Press the button.

ENTER

The buttons for the selected input

and the selected outputs turn off.

Press the Enter button to

confirm the configuration

change.

ENTER

3 4 8

= unlit or background

illumination

= lit,

Legend:

= blinking.

InputsOutputs

Unbalanced

Balanced

L R

Ring

Sleeve(s)

Tip

Ring

L R

Ring

Sleeve(s)

Tip

Ring

Sleeve(s)

Tip

NO GROUND.

Tip

Sleeve

Tip

Sleeve

3 4 8 1

Summary of Contents

Page 1 - 3 4 8

33-1106-02 C06 07www.extron.comExtron Electronics, USA1230 South Lewis StreetAnaheim, CA 92805800.633.9876 714.491.1500 FAX 714.491.1517Extron Ele

Extron electronics 450 Plus User Manual

Browse online or download User Manual for Video switches Extron electronics 450 Plus. CrossPoint 450 Plus / MAV Plus Matrix Switchers

Summary of Contents

More documents for Video switches Extron electronics 450 Plus

Comments to this Manuals

Extron electronics 450 Plus User Manual

Browse online or download User Manual for Video switches Extron electronics 450 Plus. CrossPoint 450 Plus / MAV Plus Matrix Switchers

Summary of Contents

More documents for Video switches Extron electronics 450 Plus

Comments to this Manuals

Related products and manuals for Video switches Extron electronics 450 Plus