TP Transmitters • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the TP Transmitter Series products.
Go to www.extron.com for the complete user guide.
Pre-installation — Jumper Settings
The TP T 15HD A and TP T 15HD AV are factory congured to transmit RGB video. You can recongure them
to transmit component, S-video, or composite video by using a jumper to connect pins 1 and 2 at locations
J1 and J2 on the main circuit board (see the illustration at right).
NOTE: If using the TP T 15HD AV with a TPX 88X transmitter or with an older, unmodified receiver,
see “Audio Jumpers” in the TP T Series Transmitters User’s Manual for information on audio jumper
placement for compatibility.
CAUTIONS:
• Always disconnect power to the unit before opening the enclosure.
• Wear a wrist grounding strap when handling the circuit board.
Installation
Step 1 — Mount the Unit
Turn off or disconnect power to all equipment, and mount the transmitter as desired.
Step 2 — Connect Inputs
Attach input cables to the audio and video connectors as applicable for your TP T model.
• Composite video — Connect a composite video source device to the Video RCA jack
(TP T 15HD AV) or the G pin of the Computer Input 15-pin HD connector (TP T 15HD A).
• S-video — Connect an S-video source device to pins R (chroma) and G (luma) of the
Computer Input 15-pin HD connector.
• Component video — Connect a source device to pins R (R-Y), G (Y), and B (B-Y) of the
Computer Input HD connector.
• RGBHV computer video — Connect an RGB source device to the female Computer Input HD connector.
• RGBS computer video — Connect an RGB source device to the female Computer Input HD connector.
• Audio input — Connect PC audio to the 3.5 mm TRS stereo jack.
• Audio input L and R pair — Connect left and right stereo audio to the RCA connector pair (TP T 15HD AV only).
NOTE: Input only analog line level audio signals on these connectors.
Step 3 — Connect Outputs
• Connect the RJ-45 cable from a TP receiver to an RJ-45 port on the TP transmitter. Terminate the cable ends according to
the TIA/EIA T 568A wiring standard (see the table below).
Pin
Wire Color
RGB Video and Audio
AV Video and Audio
SignalLevel Signal Level
1
White-green Red/V. sync+ ±0.35 VVideo+ +0.35 V
2
Green Red/V. sync– ±0.35 VVideo– –0.35 V
3White-orange
Audio and power +15 V ±0.5 V
+15 V
4
Blue Green+ +0.35 VReserved None
5
White-blue Green– –0.35 VReserved None
6Orange
Audio and power
Audio+* & power+
Audio–* & power–
±0.5
V
7
White-brownBlue/H. sync+ ±0.35 VReserved None
8
Brown
*Audio can be connected to wire pair 7 and 8 with a jumper.
Blue/H. sync– ±0.35 VReserved None
12345678
RJ-45 Connector
Insert Twisted
Pair Wires
Pins:
• If desired, connect a local monitor video cable to the Buffered Local Monitor port.
S-video,
Composite
1
1
1
1
1
1
RGB
TP T 15HD A
TP T 15HD AV
RGBH/H
R G BH/H
RGBH/H
(32 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals