68-1996-50
Rev A
11 10
4
2. In the Device Setup box, click the Data Interface drop-down box and
select either Cat6 (network port 1, item
c
on page 1) or SFP/Fibre
(network port 2, item
d
on page 1) as the cable to output or receive the
video signal (
b
on the figure at right).
3. In the Device Setup box, click the create source button to configure
the device as an encoder (
c
in the figure at right). Proceed to step 6.
— or —
In the Device Setup box, click the create display button to configure
the device as a decoder (
c
in the figure at right). A display icon
( ) appears in the Configuration box. Proceed to step 4.
NOTE: If a device is already configured, the device type is identified
and the only button available is change device type.
Click the button to display the create source and create
display buttons, and then perform step 3.
If the device reports “Device is streaming data”:
a. Change the data interface cable setting (step 2).
b. Change the device type (step 3).
c. Change the data interface cable setting back to the
desired port (step 2).
4. For a decoder, click the display icon ( ) that is in the
configuration box after you have created a display in step 3
(
d
in the figure at right). The source configuration screen
appears (below).
5
5. Click the Video Source drop-down box and then select the video source (
e
in the figure above).
NOTE: Choose rtp for unicast RTP streaming or tcp for unicast TCP streaming. See the VN-300 Matrix User Guide for more
information about these data transport methods.
6. Click the Save All button to save the configuration changes.
Indications
z Power ( ) LED — The Power LED lights green when receiving power. The LED flashes green when an over
temperature, overload, or underload condition occurs — cycle the power on and off to reset the unit.
z LAN 1 and LAN 2 LEDs — The LAN LEDs light or flash when the associated Ethernet connection is active.
z Status LED — The Status LED lights when video is present but encoder is not streaming it (unit is disabled or in standby
mode). The LED flashes when the unit is streaming or receiving video.
z Alarm LED — The Alarm LED lights when a critical alarm has occurred.
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada
Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2010 Extron Electronics. All Rights Reserved. www.extron.com
LAN-1
LAN-2
STAT
ALARM
3
2
4
NOTE: The display icon is available only
after you create a display in step 3.
VN-Matrix300•SetupGuide
(4 pages)
(137 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals