Extron-electronics MLS 608 D Series Setup Guide User Manual download pdf (Page 3)

Unbalanced Output Balanced Output

Tip

NO Ground Here

Sleeve(s)

Tip

NO Ground Here

AUDIO

Tip

Ring

Sleeve(s)

Tip

Ring

AUDIO

CAUTION

For unbalanced audio, connect

the sleeve(s) to the ground contact.

DO NOT connect the sleeve(s)

to the negative (-) contacts.

Installation and Cabling

Step 1 — Mount the Switcher

Turn off or disconnect all equipment power sources and rack mount

the MLS 608 D using the two supplied brackets (see image at right).

Step 2 — Connect MLS 608 D Inputs

Video — Connect inputs from video sources to the applicable connectors marked “Inputs” (see b, d, and g on page 1 for

connector types).

b Inputs 1-3 — RGB (RGBHV, RGBs, or RGsB), component (bi- or tri-level), S-video, or composite video signals. See rear cover

for connector pin-out table.

d Input 4 — Universal MTP (video and audio) input on CAT 5, 5e, or 6 twisted pair cabling

CAUTION: Do not connect the MTP cable to any LAN port, telecommunications network, or digital video output port.

Likewise, do not connect a LAN cable to any MTP, or digital video output port.

g Inputs 5-8 — Digital HDMI (HDMI 1.3) and DVI-D (using an adapter cable) inputs

Audio — Connect inputs from audio sources to the applicable connectors marked “Inputs”

(see d, i, and j on page 1 for connector types).

i Inputs 1-3 and 5-8 (line level analog stereo). Wire as shown

at right.

d Input 4 (see d above).

NOTE: HDMI inputs 5-8 have the capability to de-embed source input audio (default setting).

j Mic/line inputs 1-2 (mono). Wire as shown at right.

NOTE: These inputs have +48 V phantom power available, and the LEDs light when power is present. This power is

turned on or off via software. “Off” is the default setting.

Unbalanced Input

Balanced Input

(high impedance) (high impedance)

Ring

Sleeve (s)

Tip

Sleeve

Tip

Sleeve

Tip

Ring

Do not tin

the wires!

(5 mm)

MAX.

2U Rack Mount

Bracket (use four

lower holes)

Balanced Mic Input

Unbalanced Mic Input

Tip

Ring

Sleeve

Tip

Sleeve

(5 mm)

MAX.

Do not tin

the wires!

Step 3 — Connect MLS 608 D Outputs

NOTE: For TP cables with RJ-45 connectors, use the same standard (T568A or T568B) at both ends. See rear cover for details.

Video — Connect video output devices to the applicable connectors marked “Outputs” (see c, f and h on page 1).

c Buffered output — This signal is always tied to input 1, RGB (RGBHV, or RGBs), component (bi- or tri-level),

S-video, or composite video signals.

f Analog video output from inputs 1-4, output on CAT 5, 5e, or 6 twisted pair cabling to the MTP/HDMI U R receiver

(see



on page 1)

h Digital video and RS-232 outputs on CAT 5, 5e, or 6 twisted pair cabling to MTP/HDMI U R receiver (see



on page 1)

Audio — Connect audio output devices to the applicable connectors marked “Outputs” (see f, k and l on page 1).

f MTP analog audio output (line level mono only) on CAT 5, 5e, or 6 twisted pair cabling

k Two line level audio outputs.

Wire as shown at right.

l Power ampliﬁer output, either as

2-channel stereo, 20 watts per channel (MLS 608 D SA model) or mono audio, 40 watts per channel,

70 volts (MLS 608 D MA model). Wire as shown at below right.

CAUTIONS: • Do not connect L and R output channels to each other,

or to ground. Doing so will short the outputs and

damage the ampliﬁer.

• Do not short the “ +” and “_” connectors together.

Doing so will damage the ampliﬁer.

NC NC

To 70 V Speaker

5 mm Captive Screw

MLS 608 D MA Wiring

To 4/8 Ohm

Speaker Load

5 mm Captive Screw

MLS 608 D SA

Wiring

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Extron-electronics MLS 608 D Series Setup Guide User Manual Page 3

Comments to this Manuals

Related products and manuals for Accessories for video Extron-electronics MLS 608 D Series Setup Guide