Extron-electronics MLS 608 D Series Setup Guide User Manual download pdf (Page 6)

MLS 608 D Series • Setup Guide (Continued)

Front Panel Features

All models have the following front panel features:

MLS 608 D

AUX

VID

DOC

CAM

Blu-ray

VOLUME

SOURCE SELECTION

CONFIG

MIC VOLUME

AV Switcher with ProDSP

™

LAPTOP

12345678

a Power/reset status LED d Input selection buttons (8)

b Reset button (recessed) e Program volume control (adjustment knob)

c USB conﬁguration port f Mic volume control (adjustment knob)

Front Panel Operation

NOTE: For operation details for all models, see the MLS 608 D Series User Guide, available at www.extron.com.

a Power/reset status LED — This LED lights green when power is applied, and amber when in standby mode. It also indicates

the reset mode when the reset button is being operated (see below).

b Reset button — In order to reset the MLS switcher to one of two available reset modes via the front panel, press and hold

this recessed button in and observe the LED for conﬁrmation of unit resetting.

Reset Mode 1, Use factory ﬁrmware — To reset temporarily to the factory default ﬁrmware, press and hold the reset

button in while applying power to the unit.

NOTES: • After a Mode 1 reset, update the rmware to the latest version. DO NOT use the factory rmware resulting

from the reset. Factory ﬁrmware must be re-uploaded if that is the version to be used.

• If you do not want to update the rmware, recycling the power reinstates the rmware version used before

the Mode 1 reset.

Reset Mode 5, Reset to factory default — To reset the device to factory defaults (with the exception of the ﬁrmware),

press and hold in the reset button for approximately 9 seconds, until the LED blinks three times (once at 3 seconds,

6 seconds, and 9 seconds), and then release.

Within 1 second press and release the reset button once (<1 second). Nothing will happen if the momentary press

is not made within 1 second.

c Front panel mini USB conﬁguration port — Connect a computer to this port, using a mini USB cable (not supplied), for

conﬁguration, control, and ﬁrmware upgrades.

NOTE: For details of device conﬁguration via software, SIS commands, and ﬁrmware updating for all models, see the

DSP Conﬁgurator Help ﬁle or the MLS 608 D Series User Guide, both available at www.extron.com.

d Source selection buttons — Use these buttons to select or switch between inputs. The button lights amber to indicate which

input is active.

e Program volume adjustment knob — Use this to set or adjust the program output

volume (attenuation, from -100 dB to 0 dB) as desired. The LEDs indicate the volume

level (all off at -100 dB, all on at -4 to 0 dB). Rotate the knob clockwise to increase

volume, counter-clockwise to decrease volume. See table at right for LED/dB values.

f Mic volume adjustment knob — Use this knob to set or adjust the volumes of the two

mic inputs (see page 1, j ) as desired. The LEDs indicate the volume level.

Rotate the knob clockwise to increase volume, counterclockwise to decrease volume.

NOTE: The system and microphone volume settings and adjustments

can be made using Extron DSP Conﬁgurator program or via SIS

commands. See the MLS 608 D User Guide for details.

VOLUME

LED equivalent

dB value

-4 to 0

-9 to -5

-14 to -10

-19 to -15

-29 to -20

-49 to -30

- 69 to -50

-99.9 to -70

-100 (all LEDs off)

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Extron-electronics MLS 608 D Series Setup Guide User Manual Page 6

Comments to this Manuals

Related products and manuals for Accessories for video Extron-electronics MLS 608 D Series Setup Guide