Extron-electronics HDMI 201 User Manual

68-1375-01 Rev. D04 10HDMI Twisted Pair ExtenderHDMI 201User GuideDVI & HDMI Extenders

UL guidelines for rack mountingThe following Underwriters Laboratories (UL) guidelines pertain to the installation of an HDMI 201 unit onto a rack.1.

1U Universal Rack Shelf Figure 3. Mounting the Transmitter or Receiver on a Universal Rack ShelfFurniture mountingUnder-furniture mountingThe unit can

Through-furniture mountingThe transmitter or receiver can be mounted through a desk or other furniture using an optional Extron MBD 129 through-desk m

Projector mountingThe receiver can be mounted on a projector bracket using either of the following optional Extron projector mounting kits:• PMK 300

NOTE: The PMK 300 has a hole in the bottom plate that allows the projector pole to be inserted through the center of the plate (figure 7), rather than

PMK 350 mountingMount the receiver to a PMK 350 bracket as follows:1. Remove the front and rear plates from the PMK 350 (figure 8), using an Extron Tw

7. Align the two slotted holes in the bottom of the L-shaped bracket with the two slotted holes in the base of the tray. Secure the L-shaped bracket

Decora Unit MountingThe HDMI 201 A D (Decora) transmitter and receiver can be installed in a one-gang electrical wall box with a Decora wall plate cov

1. If a wall box is not available to use for a template, see the dimensions on page 35 to create a template. If installing directly into furniture,

Final installationAfter testing and making any adjustments, do the following:1. At the power outlet, unplug the power supply.NOTE: One power supply

This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipme

ConnectionsTransmitter ConnectionsThe wall-mountable transmitter is in an enclosure that can be mounted in UL standard wall boxes with Decora-style fa

HDMI 201 Tx Rear PanelPOWER12V 0.4A MAXRS-232PASS THRUTx Rx1 2HDMI INPUTHDMI 201 TxPOWER12V 0.4A MAXDO NOT CONNECTTO LAN12OUTPUTSHDMI

e Transmitter output ports — Connect one end of two separate TP cables to these RJ-45 female connectors on the transmitter.CAUTION: Do not connect th

Receiver ConnectionsThe rack-mountable receiver is in quarter rack width enclosure. The wall-mountable receiver is in an enclosure that can be mounte

HDMI 201 A D Rx Front PanelOUTPUTRxTxRS-232PASS THRUAUDIO-RHDMIAUDIO-L10129Figure 18. HDMI 201 A D Rx Front Panel Connectorsh Receiver input ports —

j RS-232 connector — Connect a serial communications port to this 3.5 mm, 3-pole captive screw connector for bidirectional RS-232 communication. See

TP cable terminationFigure 21 details the recommended termination of TP cables with RJ-45 connectors in accordance with either the TIA/EIA T 568A or t

Terminating shielded cableThe Tx and Rx each include two shielded RJ-45 connectors and a length of self-adhesive shielded tape that you can use to mak

Power supply wiringNOTES: • Only one power supply is required. A single power supply connected to either unit in the pair powers both units. • A

RS-232 connector wiringFigure 26 shows how to wire the RS-232 connector for non-Decora and Decora units.GroundReceive pin on connected unitTransmit pi

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

OperationFigure 27 shows the power indicator on the non-Decora and Decora models.NOTE: Two units are shown. All transmitter and receiver models have

System OperationAfter the transmitter, the receiver, and their connected devices are powered up, the system is fully operational. If any problems are

TroubleshootingHDMI signals run at a very high frequency and are especially susceptible to bad video connections, too many adapters, or cables that ar

Modulated IR Pass Through ApplicationFigure 29 shows an installation in which the Tx/Rx pair sends a modulated infrared (IR) signal across the link.

Reference InformationThis section discusses the specifications, part numbers, and accessories for the HDMI 201. Topics that are covered, include:• Sp

Audio — HDMI 201 A D Tx/RxGain ... Unbalanced output: 0 dB; balanced output: +6 dBFrequency response ..

Control/remote — external device(pass-through)Serial control port inputTransmitter ... RS-232 via (1) 3.5 mm, 3 pole captive sc

Part NumbersTransmitter/Receiver Pair Part NumbersNOTE: The Tx/Rx is comprised of the transmitter and receiver pair. The transmitter and receiver ca

Mounting AccessoriesIncluded parts Part numberRSF 123 3-inch deep 1U rack shelf kit 60-190-20RSB 123 3-inch deep 1U rack shelf 60-604-21RSU 126 6-i

Decora Template DimensionsIf you need to create a template, use the dimensions shown on figure 37, below.NOTE: The drawing is not full size or to scal

ContentsIntroduction ... 1About this Manual ... 1About the HDMI 201 T

Extron WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purc

Introduction• About this Manual• About the HDMI 201 Transmitter and Receiver• FeaturesAbout this ManualThis manual describes the Extron® HDMI 201 f

There are two subsets of transmitters and receivers in two different enclosures or form factors:• HDMI 201 Tx/Rx — These units are housed in quarter

TP Cable AdvantagesTwisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial or HDMI cable. These transmitter and re

FeaturesTransmits single link HDMI signals over two CAT 5/5e/6 cables — Standard twisted pair cables provide an economical, easily installed cable sol

Installation and OperationThis section describes the installation and the operation of the HDMI 201, including:• Mounting the Transmitter or Receiver