Extron-electronics ISM DVI Output Board User Manual download pdf

The Extron

ISM DVI is a

universal video and RGB

scaler board with DVI

output, for use with the

ISM 824. It also has a DVI

connector and a local audio output. The board mounts in one of the four vertical

expansion slots (numbered 1 to 4) at the rear of the ISM 824.

Refer to the ISM 824 User Guide, online at www.extron.com for operating details.

To install an ISM DVI output board in the ISM 824 base unit:

1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.

2. Select an open slot at the rear, or take out a blank plate by removing the two

retaining screws (top and bottom), and lifting the plate away.

NOTE: Retain and re-use the screws to secure the new output board in place.

Retain the blank plates. If a board is already installed in the desired slot,

remove the screws and carefully pull out the board.

3. Holding the new board by the frame,

align the front (non-connector end) of the

board with the top and bottom plastic

guides in the ISM 824. Slide the board in

carefully, keeping within the guides. Push

it into place ﬁrmly, and secure it with the

retained screws.

4. If required, repeat steps 2 through 4

for any other output boards.

5. Power on the ISM 824. The new output

board(s) is autodetected, and takes

approximately 30 seconds to initialize.

The 16 character LCD display indicates the new board type, slot used, and counts

down the initialization time.

See inset for example display of a new ISM DVI board

installed in slot #3, with 8 seconds left.

6. Connect a suitable display device to the DVI connector. The output can be

conﬁgured via the front panel (see page 2) or by SIS

™

commands (see page 3).

7. Insert a 5-pole captive screw connector into the local audio output connector

for balanced or unbalanced stereo output. Wire the connector as shown below.

100

240

50/60 Hz

1.2A MAX.

2 3 4 5 6 7

1 2

3 4 5 6 7 8

INPUTS

OUTPUTS

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

PASS THRU

INPUTS

RESET

LAN

REMOTE

RS232/RS422

ACT

LINK

OUTPUT

VIDEO

SCALER

70-545-01

R-Y

G/Y

B-Y

OUTPUT

UNIV.

SCALER

70-544-01

R-Y

G/Y

B-Y

OUTPUT

PASS

THRU

70-547-01

R-Y

G/Y

B-Y

Extron

ISM 824

Integration Scaling

Matrix Switcher

Align output board

with top and bottom

plastic guides.

R-Y

G/Y

B-Y

OUTPUT

SCAN

CONV.

70-546-01

Example Output Board Installation

New Univ DVI

Slot #3 08

ISM DVI

DVI

UNIVERSAL

SCALER

DVI-D

ISM DVI Output Board • Setup Guide

Unbalanced Stereo Output

Balanced Stereo Output

Tip

Ring

Sleeve(s)

Tip

Ring

L R

Left

Right

Tip

Sleeve(s)

Tip

L R

Left

Right

NO GROUND HERE.

CAUTION: For unbalanced audio, DO NOT connect the sleeves to the

negative contacts. Connect to center ground contact.

1 2 3 4

Summary of Contents

Page 1 - Balanced Stereo Output

The Extron® ISM DVI is a universal video and RGB scaler board with DVI output, for use with the ISM 824. It also has a DVI connector and a local audi

Page 2 - ISM DVI conﬁguration menu

ISM DVI Output Board • Setup Guide, cont’dISM DVI conﬁguration menuUsing the front panel menu buttons (Menu and Next), the ISM DVI conﬁguration menu c

Page 3

Output ConﬁgThe Output Conﬁg submenu displays and allows changes to be made to the resolution and refresh rate. Use the adjust knobs to select a resol

Page 4 - 68-1123-64

Extron USA - West Headquarters+800.633.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.633.9876Inside USA / Canada

Comments to this Manuals

No comments

Extron-electronics ISM DVI Output Board User Manual

Browse online or download User Manual for Hardware Extron-electronics ISM DVI Output Board. Extron Electronics ISM DVI Output Board User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Extron-electronics ISM DVI Output Board