Extron-electronics PPS 35 Installation User Manual download pdf

IMPORTANT:

Go to www.extron.com for the

complete system installation guide,

instructions, and specifications.

PPS 35 • Installation Guide

The Extron® PPS 35 Priority Page Sensor works with the

Extron PVS 405D PoleVault

Digital Switcher only and is an

optional part of a PoleVault, PlenumVault

™

, or WallVault

system.

The PPS 35 mounts to the front face of any public address

(PA) loudspeakers. When the Priority Page Sensor senses a

PA system broadcast, it sends a signal to mute the audio

output of the switcher for the duration of the PA broadcast.

The sensor unit is mounted onto the speaker with the pre-installed hook-and-loop

fastener. The cable is connected to the rear panel 3-pole captive screw Paging

Sensor port of the PVS 405D switcher, located up to 50 feet away. Fifteen feet of

cabling is supplied already attached to the sensor.

The paging sensitivity is set and controlled from the switcher via the front panel

encoder, Simple Instruction Set (SIS

™

) commands, or conguration software.

NOTES:

• The PPS 35 unit is NOT plenum rated and should not be installed above a drop

ceiling.

• The cable attached to the PPS 35 unit IS plenum rated and may be installed

above a drop ceiling.

• The PPS 35 is NOT compatible with PVS 204SA Plus, PVS 305SA,

PVS 305SA IP switchers, or with the PPC 25 Priority Page Controller.

Figure 1. PPS 35

Pre-Installation

Avoid placing the PPS 35 and PA speaker in noisy areas where the sensor can

inadvertently falsely trigger the switcher to mute the program audio.

Examples of noisy areas are:

• Crowded areas (such hallways and entrances)

• Near an HVAC system vent

• Close to the PoleVault system speakers or

other audio speakers

Installation

1. Using the hook-and-loop fastener,

attach the PPS 35 to the front grille of a paging

system speaker (see gure 2) that is located within

fty feet of the PVS 405D.

2. Run the attached cable to the switcher location.

3. Connect the end of the three-wire cable to the Paging

Sensor port on the rear panel of the PVS 405D.

Wire the connector as shown in gure 3.

4. Test and congure the PPS 35 using the PVS 405D front

panel, SIS commands, or the conguration software.

See side 2 for method.

PRELIMINARY

Figure 2. Fix PPS 35 to Speaker Grille.

PVS 405D

Paging Sensor Port

AUDIO OUT

PVS 405D

PAGING

SENSOR

AUX

VOICELIFT

INPUT 5

UDI

INPUT

AUX

ELIF

Red (+V)

Black (+)

Drain Wir

e (-)

Figure 3. Wire and Connect the

PPS 35 to the PVS 405D.

1 2

PRELIMINARY 1
68-2468-01 2

Summary of Contents

Page 1 - PRELIMINARY

IMPORTANT:Go to www.extron.com for the complete system installation guide, instructions, and specifications.PPS 35 • Installation GuideThe Extron® PPS

Page 2 - 68-2468-01

PPS 35 • Installation Guide (Continued)Extron USA Headquarters+1.800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron USA - East+1.714.491

Comments to this Manuals

No comments

Extron-electronics PPS 35 Installation User Manual

Browse online or download User Manual for Hardware Extron-electronics PPS 35 Installation. Extron Electronics PPS 35 Installation User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Extron-electronics PPS 35 Installation