Extron electronics PVS 405D Setup Guide download pdf

Product Category

PVS 405D • Setup Guide

The Extron

PVS 405D is a ve input, one HDMI

output switcher with a built-in audio amplier and

a 3-port Ethernet switch. It is part of the PoleVault

PlenumVault

, and WallVault

Digital Systems, and

is used in conjunction with the Extron PVT digital

series of transmitters and Extron speakers. The PVS 405D accepts HDMI and high resolution (RGB) video and audio signals. The

RGB input is digitized at the PVT input wallplate. In addition, it has dedicated ports for connecting the optional VoiceLift

system

and a Page Sensor unit for facility communications.

NOTE: For full installation, configuration, connector wiring, and operation details, see the PVS 405D User Guide, available at

www.extron.com.

Installing and Cabling the PVS 405D Switcher

The PVS 405D may come already pre-mounted in the Extron PMK 560 (Projector Mount Kit) and the PVM 220 (PlenumVault

Mount Kit).

However, if it is not pre-mounted, to mount the PVS 405D, follow the steps in the system installation guide, supplied with the

complete PoleVault, PlenumVault, or WallVault System. Alternatively follow the steps in the relevant Setup Guide for the mounting

kit (PMK 560, PVM 220, WMK 160, or USFM 100). Connect the cables to the switcher as shown below.

ATTENTION: The PoleVault signal transmission method is specic for PVS 405D switchers working with PVT digital wallplates.

DO NOT connect the input ports to an MTP system or to an Ethernet/LAN or data transmission system.

PVS 405D

POLEVAULT SWITCHER

AUDIO LEVEL ADJUSTINPUTS

SELECT

CONFIG

PEAK

NORMAL

SIGNAL

INPUT

AUX

AUDIO

PEAK

NORMAL

SIGNAL

VOICELIFT

PAGING

SENSOR

SENSITIVITY

3A MAX

POWER

12V

HDMI

1/2

SIG LINKSIG LINK

3/4

INPUTS OUTPUT AUDIO OUT

PVS 405D

PAGING

SENSOR

PVT IN PVT IN

AUX OVER PVT REMOTE

VOICELIFT

LAN 1 LAN 2 LAN 3

INPUT 5

RS-232

Tx Rx

SG G

HDMI Output

to Display Device

HDMI

Connector

Aux Audio

Input 5

Audio Output to Speakers

Red Positive (+)

Black Negative (-)

Speaker

wire color

PVS terminal

(left and right)

Line Out

Output (Audio)

Paging

Sensor

Input

Aux

Input

Supplied PVS Switcher

Exter

nal Power Supply

(12 VDC, 4 A max.)

3-port 10/100 Ethernet Switch

Connect to ports as follows:

1. TCP/IP network

2. MLC controller

3. Optional network device

Power Connector

HDMI/RGB

PVT SW HDMI RGB D

HDMI or RGB video/audio, Inputs1/2 and 3/4

1 STP cable with RJ-45 connectors

VGA IN

AUDIO

IN OUT

LOCAL OUT

AUDIO IN

HDMI IN

IR OUT

6 2 3

VoiceLift

Receiver

IR control

MLC 104 IP Plus

RS-232 input

White Tx on RS-232 port

Violet Rx on RS-232 port

Drain wire Ground (G)

Black PVS Power Supply (–)

Red PVS Power Supply (+)

MLC

wire color

To PVS terminal

MLC 104 IP Plus right side

panel MLS and Power ports

RS-232 12V

MLS PWR

GROUND

+12V IN

Ground

+12 VDC input

To Supplied

PVS Switcher

Power Supply

(12 VDC, 4 A max.)

NOTE: If you use cable that

has a drain wire, tie the drain

wire to ground at both ends.

NOTE: You must

connect a ground

wire between the

MLC and PVS.

Ground (Gnd)

Transmit (Tx)

Receive (Rx)

Transmit (Tx)

Receive (Rx)

DO NOT

GROUND

OR SHORT

SPEAKER

OUTPUTS

4/8

AMPLIFIED AUDIO OUT

CLASS 2 WIRING

NOTES:

• The PVS 405D is capable of receiving signals from PVT wallplates located up to 150 feet (45 m) away.

• RJ-45 termination must comply with the TIA/EIA T 568A or 568B wiring standards for all connectors. The same standard

MUST be used at both ends of all cables. Refer to the PoleVault System Installation Manual for details. The cables

supplied with the PoleVault system are terminated to the TIA 568A standard.

• The use of shielded cable, such as Extron STP201 or Extron XTP DTP 24 cable, is strongly recommended.

Figure 1. PVS 405D Switcher Connections

1 2 3 4

Summary of Contents

Page 1 - Product Category

Product Category1PVS 405D • Setup GuideThe Extron® PVS 405D is a ve input, one HDMI output switcher with a built-in audio amplier and a 3-port Ether

Page 2 - Step 2 — Connect A/V Outputs

PVS 405D • Setup Guide (Continued)2Step 1 — Connect A/V inputsa HDMI and RGB video and audio inputs — Using recommended TP cables (see the Notes re ca

Page 3 - Step 4 — Connect power

j IR control port — Connect the wiring from the IR Out port on rear of the MLC to this connector. IR signals on this connector are passed to the conne

Page 4 - Configuration

Front Panel Operation and Conﬁguring the PVS 405D SwitcherFor full details of front panel operation and switcher conguration, refer to the PVS 405D U