TP Receivers • Installation and Operation
TP Receivers • Installation and Operation
Installation and Operation, cont’d
Audio
All Extron TP receivers receive and output stereo audio. All
receivers except the TP R 15HD A output the audio on both left
and right RCA connectors and on 3.5 mm, 5-pole captive screw
connectors. The TP R 15HD A outputs audio on the captive
screw connector only.
7
Stereo audio output connectors — Connect left and right stereo
audio cables between these rear panel RCA connectors and the
output device’s stereo audio inputs.
Only analog, line level, unbalanced audio signals can be
output on these connectors.
8
Stereo audio 5-pole captive screw connector — Connect audio
devices, such as an audio amplifier or powered speakers, to
these connectors. These 3.5 mm, 5-pole captive screw
connectors output unamplified, line level audio. Figure 2-8
shows how to properly wire an output connector.
Unbalanced Output
Tip
See caution
Sleeve
Tip
See caution
Balanced Output
Tip
Ring
Sleeve (s)
Tip
Ring
Figure 2-8 — Audio output connector wiring
CAUTION
Connect the sleeve to ground (Gnd). Connecting
the sleeve to a negative (-) terminal will damage the
audio output circuits.
If only an audio signal, no video, is received, connect a
ground wire between the chassis ground and an earth
ground in the equipment rack or other grounded device.
If the receiver is not grounded, a crackling sound may be
heard in the audio output.
Power connector
9
Power
TP R BNC AV — Plug a standard IEC power cord into this
connector to connect the TP R BNC AV to a 100 to
240VAC, 50 Hz or 60 Hz power source.
If the distance between the transmitter and receiver is too
great for the receiver to power the transmitter, the video
image will be missing, distorted, or noisy, or the
receiver’s Manual/Auto LED will flash. The transmitter
requires a local power supply.
TP R BNC A and TP R AV — Wire the external 15V power
supply into this 3-pole captive screw connector
(figure 2-9) and plug the connector into the receiver.
The power supply is included with the unit.
Power Supply
Output Cord
Captive
Screw
Connector
TP R 15HD A
Power
12VDC
Captive
Screw
Connector
TP R BNC A
TP R AV
Power
15VDC
RidgesSmooth
N/C
Figure 2-9 — Power connector wiring
TP R 15HD A — Wire the external 15V power supply into
this 2-pole captive screw connector (figure 2-11) and
plug the connector into the receiver. The power
supply is included with the unit.
Termination of TP cable
Figure 2-10 details the recommended termination of TP cables in
accordance with the TIA/EIA T 568A wiring standards.
Clip DownSide
1
1&2
3&6 4&5
7&8
2345678
12345678
Pin Wire color
RGB video and audio AV Video and audio
Signal Level Signal Level
1 White-green Red/V. sync+ ±0.35V Video+ +0.35V
2 Green Red/V. sync- ±0.35V Video- -0.35V
3 White-orange
Audio &
power
+15V with
±0.5 V
+15V
4 Blue Green+ +0.35V Reserved None
5 White-blue Green- -0.35V Reserved None
6 Orange
Audio &
power
Audio+* &
power+
Audio-* &
power-
±0.5 V 0V
7 White-brown Blue/H. sync+ ±0.35V Reserved None
8 Brown
* Audio can be jumpered to wire pair 7 and 8.
See
Audio jumpers
in this chapter.
Blue/H. sync- ±0.35V Reserved None
RJ-45
connector
Twisted
Pairs
Figure 2-10 — TP cable termination
2-14 2-15
(6 pages)
(48 pages)
(53 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals