Extron-electronics YCS SW2 A User Guide User Manual download pdf (Page 8)

YCS SW2 A • Installation and Operation

Installation and Operation

YCS SW2 A • Installation and Operation

2-2

2-3

Rack mounting

For optional rack mounting, do not install the rubber feet.

Mount the switcher on any of the following rack shelves:

• RSB 123 1U, 3.5" Deep VersaTools Basic Rack Shelf (part

#60-604-20)

• RSF 123 1U, 3.5" Deep VersaTools Rack Shelf Kit (part

#60-190-20)

• RSB 126 1U, 6" Deep Basic Rack Shelf (part #60-604-10)

• RSU 126 1U, 6" Deep Universal Rack Shelf Kit (part

#60-190-10)

• RSB 129 1U, 9.5" Deep Basic Rack Shelf (part #60-604-01)

• RSU 129 1U, 9.5" Deep Universal Rack Shelf Kit (part

#60-190-01)

• MBU 123 Mini Under-desk Mount Kit (part #70-212-01)

• MBB 100 Back-of-Rack Mount Kit (part #70-367-01)

• Projector mounting kits: PMK 100 (part #60-217-01),

PMK 250, (part #70-526-02 or 70-526-03), PMK 300 (part

#70-374-01), PMK 350 (part #70-563-02 or 70-563-03), or

PMK 450 (part #70-618-02 or #70-618-03).

UL rack mounting requirements

The following Underwriters Laboratories (UL) requirements

pertain to the safe installation of the equipment in a rack.

1. Elevated operating ambient temperature — If the

equipment is installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the

rack environment may be greater than room ambient

temperature. Therefore, install the equipment in an

environment compatible with the maximum ambient

temperature (Tma = +113 °F, +45 °C) speciﬁed by Extron.

2. Reduced air ﬂow — Install the equipment in a rack so that

the amount of air ﬂow required for safe operation of the

equipment is not compromised.

3. Mechanical loading — Mount the equipment in the rack so

that a hazardous condition is not achieved due to uneven

mechanical loading.

4. Circuit overloading — Connect the equipment to

the supply circuit and consider the effect that circuit

overloading might have on overcurrent protection and

supply wiring. Appropriate consideration of equipment

nameplate ratings should be used when addressing this

concern.

Installation Overview

To install and set up the YCS SW2 A, follow these steps:

Mount the YCS SW2 A on a rack shelf, furniture, or

projector mount if desired.

Connect your composite video and/or S-video input

source(s) to one or both YCS input connectors.

Connect your output device(s) to the YCS composite video

and/or S-video output connector(s).

Connect the audio connectors of your input sources to the

YCS audio input connectors.

Connect the audio connectors of your output device(s) to

the YCS audio output connectors.

If necessary, wire the provided 2-pin captive screw

connector to the external power supply. (See “Wiring the

Power Connector,” later in this chapter.)

If using autoswitching, insert the provided 3-pin captive

screw plug into the 3-pin connector on the YCS back panel,

and jumper-connect pins 1 and 2, and 2 and 3, together.

(See “Autoswitching,” later in this chapter.)

If using contact closure for input selection, connect a

remote contact closure device to pins 1, 2, and of the

captive screw connector on the YCS rear panel. (See

“Contact Closure,” later in this chapter.)

Apply power to the YCS SW2 A and to the input and

output devices.

Mounting the YCS SW2 A

The YCS SW2 A can be set on a table; mounted on a rack shelf;

mounted under a desk, podium, or table; or attached to a

projector mount.

Tabletop use

Four self-adhesive rubber feet are included with the YCS SW2 A.

For tabletop use, attach one foot at each corner on the bottom of

the unit, and place the YCS in the desired location.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 18 19

Comments to this Manuals

No comments

Extron-electronics YCS SW2 A User Guide User Manual Page 8

Comments to this Manuals

Related products and manuals for Audio accessories Extron-electronics YCS SW2 A User Guide