Extron electronics 14400 Setup Guide download pdf (Page 8)

8 FOX Matrix 320x and FOX Matrix 14400 • Installation 9FOX Matrix 320x and FOX Matrix 14400 • Installation

Making Connections

Fiber optic boards with connectors and LEDs —

WARNING: This unit outputs continuous invisible light, which

may be harmful to the eyes; use with caution. For additional

safety, plug the attached dust caps into the optical transceivers

when the ber cable is unplugged.

AVERTISSEMENT : L'appareil émet une lumière invisible en

continu, à utiliser avec precaution. Branchez les protections

contre la poussière dans l'ensemble émetteur/récepteur lorsque

le câble bre optique est débranché.

NOTES:

• Ensure that you use the proper ber cable for your I/O

board. Typically, singlemode ber has a yellow jacket and

multimode cable has an orange or cyan jacket.

• The FOX matrix switcher uses one

connector on the block as an input

and the second connector on the

same block as a separate output.

Input connector — Connect a fiber

optic cable between each Input LC

connector and a FOX 500 Tx or any

other compatible Extron FOX device.

NOTE: Or, for the serial return

(receiver-to-transmitter) function,

connect the far end to the Optical

2 connector on a FOX Rx receiver.

Input LED — See Fiber optic I/O LED

indications on page 10.

Output connector — Connect a fiber

optic cable between each output LC

connector and a FOX 500 Rx or any

other compatible Extron FOX device.

NOTE: Or, for the serial return

(receiver-to-transmitter) function,

connect the far end to the

Optical 2 connector on a FOX Tx

transmitter.

Output LED — See Fiber optic I/O

LED indications on page 10.

OUT

OPTICAL

2* 1

OPTIONAL FOR

RETURN DATA

LINK

OPTICAL

ansmitting

Unit

Receiving

Unit

FOX Matrix

Switcher

12*

OPTIONAL FOR

RETURN DATA

LINK

ÕÎÎ

3G HD-SDI, HDI-SDI, and SDI boards with DIN

OUT

ÖÖ

ÏÏ

connectors —Connect inputs and output using the

included DIN-to-female-BNC pigtail connectors, as

follows:

NOTES:

• The pigtails are not installed on the board

during shipment.

• To install the pigtails, press them onto the

DIN connectors until they snap into place.

• To remove the pigtails, pull back on the

knurled collar and pull the pigtail straight

back from the DIN connector.

Multi-rate SDI Input connectors — Connect

HD-SDI, SDI, or 3G-SDI video inputs to these BNC connectors.

Multi-rate SDI Output connectors — Connect digital displays to

these BNC connectors.

Remote RS-232/RS-422 port — If desired, connect a control system

or computer to the rear panel Remote RS-232/RS-422 port.

RS-232 Function Pin Function

—

Gnd

—

Not used

Transmit

Receive

Not used

Ground

Not used

—

Tx–

Rx–

—

Gnd

—

Rx+

Tx+

—

Not used

Transmit (–)

Receive (–)

Not used

Ground

Not used

Receive (+)

Transmit (+)

Not used

RS-422

Figure 5. Audio Output Connector Wiring

LAN port — If desired, connect a network WAN or LAN hub, a

control system, or a computer to the Ethernet RJ-45 port.

Network connection — Wire as a patch (straight) cable.

Computer or control system connection — Wire the interface cable

as a crossover cable.

NOTE: The factory default IP address is 192.168.254.254.

Reset button — Initiates four levels of reset of the matrix switcher.

For different reset levels, press and hold the recessed button while

the switcher is running or while you power up the switcher.

See the FOX 320x and 14400 Series User Guide, available at

www.extron.com.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 18 19

Comments to this Manuals

No comments

Extron electronics 14400 Setup Guide Page 8

Comments to this Manuals

Related products and manuals for Recording Equipment Extron electronics 14400