Extron-electronics PoleVault Digital Switcher Systems PVS 405D User Manual

featuring the PVS 405D Switcher Includes installation details for the PoleVault (PMK 560), WallVault (WMK 160 and USFM 100), and PlenumVault (PVM 220

• Ceiling and wall type (important in assessing the hardware needed)• Ceiling type: dropped, spline, hard lid, and similar. Structural type (wood, c

Location of MediaLink Controller and Wall Plates• Forward and side reach (for full details refer to a copy of ADA Standards for Accessible Design, Se

Inventory — PoleVault Digital SystemPoleVault Digital System42-207-03 or 42-208-03PMK 560Pole Mount KitPMK 560 White70-1034-03(4) 10-32 Cover screws(

Kits• PVS 200D (part number 42-207-03) includes one PVT SW HDMI D• PVS 400D (part number 42-208-03) includes one PVT SW HDMI RGB D and one PVT SW HD

Inventory — WallVault Systems (USFM 100)ExtronUSFM 100Plastic Enclosure CoverBoom ArmBase PlateArm Cover (buttom)Arm Cover (top)Arm Cover (front)Devic

Inventory — WallVault Systems (WMK 160)Figure 6. WMK 160 for WVS 210D and WVS 410D WallVault Systems42-211-03 WVS 210DPart Number Description Quantit

Inventory — PlenumVault Systems (PVM 220)PVS 405SA IPPOLEVAULT SWITCHERINPUTSAUDIO LEVEL ADJUSTPAGINGSENSORSENSITIVITYPEAKNORMALSIGNALVOICELIFTPEAKNOR

Inventory — PlenumVault Systems (PVM 220)42-230-03 PLS 210DPart Number Description Quantity26-621-50 MLC IR cable, 50 ft 126-626-50 MLC PW/RS-232 cabl

• Drywall saw and hacksaw blade mounted on handle (for cutting ceiling tiles)• Flashlight and safety goggles• Razor knife• 2 inch hole saw• Paint

Optional ItemsThe optional Extron products suggested below can be added to or substituted for items in the standard Digital PoleVault System. Some of

Safety InstructionsSafety Instructions • EnglishWARNING: This symbol, , when used on the product, is intended to alert the user of the presence of u

PoleVault Digital Systems • Introduction14

InstallationOverviewThis section outlines the basic steps for installing the PoleVault System. An outline and checklist of the stages (Stages One thro

Outline of Installation Steps for PoleVault Digital SystemsStage 1 — Install the Screen and Projectorc Mark the screen location (page 18).c Install

PCM 340 Projector Drop Ceiling Mount a • Where it goes: Attaches to a structural ceiling, rests on the suspended ceiling.• What it do

1. Mark Screen Location.TIPS:• When marking the location of screens, devices, or the site for installing transmitters and MediaLink control devices,

ï Screw the adjuster plate onto the base of the pipe. d. Using a 3/32 inch hex wrench, back out the set screws on the top portion of the adjuster pl

Using the slot closest to the barrel, secure thearms to the bracket withthe clamp and screw.vi. Pivot the arms so that they extend towards the center

ix. Check for stress on the arms. To do this loosen the mounting screws (do not remove). If the arm or the barrel lifts, this indicates stress on the

à Mark the structural ceiling for lag eye bolt installation.4. Cut the Ceiling Tile.a. Mark the location of the PCM 340 on the T-frame. This aids p

6. Finish Projector Drop Ceiling Mount Installation.a. Detach the projector bracket and projector from the adjuster plate. DO NOT remove the projecto

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rule

å Attach the turnbuckles at the corners of the PCM 340.7. Secure the Projector Drop Ceiling Mount to the Ceiling.a. Attach the four turnbuckl

8. Install the Electrical Box (If required).WARNING: Improper installation may result in electrical shock or serious injury. All electrical installat

PoleVault Digital Systems • Installation — Stage 1 (Screen and Projector)26

Stage 2: Mounting the PVT Wallplate and the MediaLink ControllerStage 2 Involves installing and cabling the devices shown below.NOTE: The installatio

CONFIGDISPLAYVOLUMEMLC 104 IP PLUSONVCRDVDPCOFF1234Mountingscrews (4)123GROUND+12V OUTCMGROUNDIR OUTGROUNDSCPGROUNDTxRxDISPLAYRS-232/IRA B C D

NOTE: The installation must conform to national and local building and electrical codes, and UL requirements. See the device user guides for details.

2. Pull the Cables (at the input locations)The following cables need to be installed:• STP cables for signal transmission from the AV wallplates to t

3. Install the Wallplates.a. Connect the cables to the rear of the input devices.b. If desired, wire an IR emitter to the unit using a two conductor

4. Install the MediaLink Controller.TIP: Before cabling and installing the MLC 104 IP Plus, locate the device MAC address printed on a label on the bo

b. Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector controlNOTE: Some projectors require NULL connecti

Conventions Used in this GuideNotificationsThe following notifications are used in this guide:DANGER: A danger indicates a situation that will result

d. The connections between the MLC 104 IP Plus and the PVS 405D switcher should look like the figure below.e. Sliding the cables into the opening, s

Stage 3: Installing the FF 120 Ceiling SpeakersStage 3 Involves installing the devices shown below.• Where it goes: Installs in ceiling tiles at a pr

NOTE: The installation must conform to national and local electrical codes, and UL requirements. See the device guide for details.1. Cut Ceiling Tile

Repeat steps 1 and 2 for each speaker that needs to be installed, connecting the speakers according to the system preferred (for example, in parallel,

3. Terminate the Speaker Cable for the PVS Switcher.a. To terminate the cable, strip the end of the cable 0.2 inch (5 mm) and secure the wires into t

Stage 4: Installing the Switcher Mounting System and the PVS 405DStage 4 Involves installing the switcher mounting system and the PVS 405D Digital Swi

A1. Install the PMK 560 Base Plate.a. Remove the four cover screws from the center of the PMK 560 and slide the two halves apart. Remove them from th

f. Hook the combined plate and switcher into the PMK 560 base plate (see figure on page 40, °). Secure it to the base plate with two screws.ATTENTIO

A3. Secure the HDMI Cables Using the LockIt Bracket.The supplied Extron LockIt lacing bracket makes it possible to secure a standard HDMI cable to the

A4. Finish Installing the Mounting Kit.CAUTION: The PoleVault signal transmission method is specific for PVS 405D switcher working with PVT wallplates

ContentsIntroduction... 1Overview ...

B. WallVault System (WMK 160 Wall Mount Kit)B1. Install the WMK 160 Base PlateNOTES: • For masonry wall use steps a to e.• For non-masonry walls use

f. To mount the WMK 160 onto non-masonry walls, at the desired site, locate and mark the wall studs.NOTES: • For ideal installation secure the base

c. Secure the power supply to the right of the electrical outlet cutout by threading the supplied tie wraps through the loops on the base plate. Atta

C. WallVault System (USFM 100 Short Throw Wall Mount Kit)• Where it goes: Installs onto a wall close the short throw projector location.• What it do

C1. Install the USFM 100 Base Plate.NOTES: • It is required to attach the base plate to two wall studs, using a minimum of four securing points• Dr

iv. Secure the mounting plate (and switcher) to the base plate by aligning the two small tabs on the back of the mounting plate over the correspondin

iii. Run the cables through the raceway or conduit to the USFM 100.C4. Cable the Switcher.Connect the cables to the switcher as shown on pages 43.NOT

b. Secure the power supply on the base plate, as close to the switcher as possible. To do this, pass the tie wraps through the holes in the base plat

D. PlenumVault System (PVM 220 PlenumVault Mount Kit)The PVM 220 is UL Listed for use in plenum airspaces: meets UL 2043 for heat and smoke release.Su

a. Remove this screw onthe right and left sidesof the mounting plate.b. Swing the mounting plate out from the door frameand slide the plate to the rig

B4. Cable the switcher ... 46B5. Final Installation ... 46C. WallVault System (USFM 1

Thread the cable down through the cablelock, through the hole on the frame of theenclosure and back up through the lock.Cable LockLocking PinD3. Suspe

Insert threaded rodsthrough holes on the endsof the mounting plate.Attach washers and nuts and secure.For threaded rod installation:NOTES: • … inch

c. Attach the metal conduit to the outer cover. NOTES: • Remove only the knockouts that are to be used for cabling. Leave intact the unused knockou

D6. Install Devices onto the Device Mounting plate.NOTE: The maximum door load is 15 lbs (6.8 kg).To mount the devices and accessories:a. Carefully

PVS 405SA IPPOLEVAULT SWITCHERINPUTSAUDIO LEVEL ADJUSTPAGINGSENSORSENSITIVITYPEAKNORMALSIGNALVOICELIFTPEAKNORMALSIGNALINPUTSELECTCONFIGR12345AUXAUDIOE

D10. Verify and Configure the Setup.Turn on the power to all the devices. Verify and configure the system. See the PVS 405D User Guide, or PVS 305SA IP

PoleVault Digital Systems • Installation — Stage 4 (PVM 220 and PVS 405D)60

ü Select online device or emulation mode (below).Stage 5: Configuring the PVS 405D SwitcherStage 5 Involves installing the programs shown below.Item

2. Configure the System — Global Configurator.a. Download and install the Extron Global Configurator (GC) configuration program (available at www.extro

3. Test the System.a. Connect all the input devices (PC, DVD, document camera, and, where desired, LAN cables, and so forth) to the transmitters and

IntroductionOverviewThis guide covers the installation of the Extron PoleVault Digital System, and also the installation methods for each type of Wall

d. Test the controller configuration as follows:• Check that the MLC is controlling the projector and PVS 405D switcher, and outputs the correct ima

Ü Slide the covers onto the PMK 560.g. Where installed, it may be necessary to adjust the sensitivity of the Priority Paging system. During a test t

b Attach the Z bracket to the ceiling tile and the back plate. g Align the arrows on the housing rim and the dome tab.ArrowReceiverDomeTwis

Optional Accessory Installation — Priority Page Sensor (PPS 35)LRDO NOTGROUNDOR SHORTSPEAKEROUTPUTS4/8Ω3A MAXPOWER12VHDMI1/2SIGLINKSIGLINK3/4INPUTSOUT

PVS 405D Paging Sensor PortAUDIO OUTPVS 405DPAGINGSENSORRAUXVOICELIFTINPUT 5+VRAUDIO OUTRINPUT 5RgPVS 405DAUXVOICELIFTRed (+V)Black (+)Drain Wire (-)a

The Priority Page Sensor Kit momentarily silences classroom audio whenever a page is made from a public address (PA) system. For detailed information,

Installation ProcedureWARNING: Risk of serious personal injury if installation is not done correctly. All structural steps, anchoring, and electrical

6. Strip 3/16 inches of insulation from each conductor on the bare wire end of the remaining blue sensor cable. Do not tin the leads. Feed the wire i

Testing and Adjustment ProcedureTo test that the classroom audio is muted when a PA system announcement (a page) occurs:1. Turn the classroom audio o

Outline of Installation Steps for WallVault Digital Systems (WMK 160)Stage 1 — Install the Screen and Projector.c Mark the screen location (page 18).

12SIGNAL4AUXSIGNALSENSITIVITYVideoAudio ControlCATxLegend:AUDIO INHDMI INIR OUTSGAUDIOIN OUTVGA INLOCAL OUTAUDIO INHDMI INIR OUTSGHDMI INAUDIO INCONFI

Outline of Installation Steps for WallVault Digital Systems (USFM 100)Stage 1 — Install the Screen and Projector.c Mark the screen location (page 18)

Outline of Installation Steps for PlenumVault Digital Systems (PVM 220)Stage 1 — Install the Screen and Projector.c Mark the screen location (page 18

Optional Accessory Installationc VoiceLift System (page 66).c Priority Page Sensor PPS 35 (page 67).c Priority Page Sensor Kit PPS 25 (page 69).The

77Extron WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pu

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +

Before You Begin — Planning the InstallationBefore installation is started, you must consider several major factors to ensure that the installation pr