Extron-electronics WMK 160 User Manual download pdf

The Extron® WMK 160 Wall Mount Kit is used for hanging WallVault

System AV products on a wall near a at screen display or short throw projector.

The WMK 160 has a 17.3 x 16.5 x 2.75 inches (43.9 x 41.9 x 6.9

cm) enclosure, and a base plate on which to mount the switcher (for

example the PVS 405D) and the associated power supply, with room

for cable management.

In addition, an accessory device can be mounted on the base plate.

The cover has knockouts on three sides that allow external raceways

to be used where needed for cabling.

WARNING: Risk of Personal Injury. Maximum load for the

WMK 160 is 15 lbs (7 kg)

NOTE: The WMK 160 is to be used only with Extron UL listed

products.

The key components (base plate, cover, and PVS switcher mounting

plate) of the WMK 160 are shown in gure 1. Included in the kit are the

following:

(4) ¼-20 x 2" pan head bolts, (4) ¼" KapToggle

assemblies,

(2) #14 x 1¾" self tapping metal/wood screws,

(4) cover screws.

Not shown but included are (3) 4-40 x ¼" screws, (2) tie wraps (15"),

(8) 4-40 x 3/16" screws (used to attach other Extron devices).

Figure 1. WMK 160 parts

(2) #14 x 1 3/4"

Self-tapping

Metal/Wood Screws

(4) 1/4-20 x 2"

Pan Head Bolts

(4) 1/4" KapToggle

Assemblies

(4) Cover Screws

(1) PoleVault Switcher

Mounting Plate

(1) WMK 160 Cover

(1) WMK 160 Base Plate

(2) #14

lf-

eta

(

(4)

Ass

(4)

(

1) Po

160 Base P

lat

(

1) WM

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this furnishing.

When using this furnishing, basic precautions should always be followed, including the following:

DANGER: Risk of Electric Shock. Disconnect power to this furnishing before cleaning.

WARNING: Risk of Electric Shock. Devices used in this furnishing should be connected to a properly grounded outlet only.

See Grounding Instructions in the device manual.

WARNING: Risk of Personal Injury. Read and follow the steps below to reduce the risk of burns, ﬁre, electric shock, or injury

to persons.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must

be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.

WMK 160 • Installation Guide

1. Always unplug devices installed in this furnishing from outlets before putting on or taking off parts.

2. Close supervision is necessary when this furnishing is used by, or near children, invalid, or disabled persons.

3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by

the manufacturer.

4. Never operate a device in this furnishing if it is not working properly, if it has been dropped or damaged, or dropped into

water. Return the device used in this furnishing to a service center for examination and repair.

5. Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.

6. Never drop or insert any object into any opening.

7. Do not use outdoors.

8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

9. To disconnect the devices, turn all controls to the off position, then remove plugs from outlet.

1 2 3 4 5 6

Summary of Contents

Page 1 - WMK 160 • Installation Guide

1The Extron® WMK 160 Wall Mount Kit is used for hanging WallVault® System AV products on a wall near a at screen display or short throw projector.Th

Page 2 - Installation

2WMK 160 • Installation Guide (Continued)Figure 3. Non-masonry wall mountingWall StudsCutout forElectrical OutletLevelMarker for Pilot HoleCutout fo

Page 3 - Step 3. — Run Cables

3vii. Align the slotted mounting holes in the base plate over the installed screws, then slide the plate down so the screw t into the s

Page 4 - — Cable the Switcher

4WMK 160 • Installation Guide (Continued)WMK 150 • Setup Guide, cont'dFigure 7. Cabling the switcher (PVS 405D shown) LRDO NOTGROUNDOR SHORTSPEA

Page 5 - — Final Installation

5WMK 150 • Setup Guide, cont'dStep 5. — Final Installation.a. After completing cabling, place the cover over the installed plate, and secure at

Page 6 - WMK 160 Dimensions

668-2384-01 Rev. A08 13WMK 160 • Installation Guide (Continued)17.07"(39.04 cm)Base Front View16.37"(32.69 cm)Both Sides1.50"(5.08 cm

Comments to this Manuals

No comments

Extron-electronics WMK 160 User Manual

Browse online or download User Manual for Hardware Extron-electronics WMK 160. Extron Electronics WMK 160 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Extron-electronics WMK 160