Extron electronics RGB 112xi Operations Instructions Page 36
- Page / 105
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-11Integration Scaling Matrix Switcher • Operation
The display or projector may require a particular combination of horizontal (H) and
vertical (V) sync signal polarities. Select the appropriate combination of positive or
negative H and V sync for the selected output by rotating the Adjust
knob.
If you need to set the sync type and polarity on the other output, press the other
output button. You do not need to exit this submenu.
Advanced Configuration menu
Figure 3-10 is a flowchart that shows an overview of the Advanced Configuration
menu, the submenus, and the available settings.
Default
Cycle
Default
Cycle
Menu
Menu
Next
10 sec.
10 sec.
Video & Audio
Configuration
Test Pattern
Color Bars
Out #1 Out # 2
Off Off
Blue Only Mode
Off
Edge Smoothing
Output #2
Menu
Output
Configuration
Menu
Advanced
Configuration
Menu
User Presets
Menu
Next
Exit Menu
Press Next to Exit
Menu
10 sec.
Output #1 Blanking
Top Bottom
000 000
RGB Delay
Out #1 0.8 Seconds
Out #2 0.5 Seconds
Auto Imaging
<
Off
>
On
Auto Memories
<
Off
>
On
Enhanced Mode
<
Off
>
On
Pixel Phase
Out #1 Out # 2
000 000
Reset Unit?
Press and Hold
BLACK/MUTE
To Reset
10 sec.
Next
Set test pattern type
• Color Bars
• Crosshatch
• 4x4 crosshatch
• Grayscale
• Crop
• Alternating pixels
• Film aspect 1.78
• Film aspect 1.85
• Film aspect 2.35
• Ramp
Select the output 1 delay
with the Adjust knob.
Select the output 2 delay
with the Adjust knob.
Change this submenu
with either Adjust knob.
Select a test pattern
with the Adjust knob.
Select preview/program
off/on with the Adjust
knob.
Select blue mode with
the Adjust knob.
Select edge smoothing
with the Adjust knob.
Display blue and sync only
• Off (default), Input 1,
Input 2, Both
Edge smoothing
• Off (default), Input 1,
Input 2, Both
To reset the switcher, press and
hold the Black button until
the reset message appears.
*Adjust knobs do not affect
this submenu.
Press an output button
to select an output.
Select top blanking with
the Adjust knob.
Select bottom blanking
with the Adjust knob.
Next
Next
Next
Next
Next
Next
Next
Select auto imaging
with the Adjust knob.
Select auto memories
with the Adjust knob.
Set the output 1 pixel phase
with the Adjust knob.
Set the output 2 pixel phase
with the Adjust knob.
10 sec. 10 sec. 10 sec.
10 sec.
PAL Film Mode
Input #2
<
Off
>
On
Next
10 sec. 10 sec.10 sec.
If necessary, select
another input and
repeat.
Select an input.
Set the PAL film mode
on or off with either
Adjust knob.
Figure 3-10 — Advanced Configuration menu flowchart
- 68-576-01 Rev. G 1
- Precautions 2
- FCC Class B Notice 3
- Setup and Operation 5
- Table of Contents 6
- Table of Contents, cont’d 7
- Chapter One 10
- Introduction 11
- Network/ 12
- Internet 12
- Introduction, cont’d 13
- Chapter Two 16
- Installation 17
- Mounting instructions 18
- Installation, cont’d 19
- RCA Connector 20
- 3.5 mm Stereo Plug Connector 20
- Optional output connection 22
- Ethernet connection 22
- RS-232 connection 24
- Chapter Three 26
- Operation 27
- 12345678 28
- Operation, cont’d 29
- LCD display 30
- Menu control buttons 30
- Adjustment knobs 30
- 10 sec.10 sec 32
- Output Configuration menu 34
- Advanced Configuration menu 36
- Video & Audio 40
- Configuration 40
- Exit Menu 40
- Press Next to Exit 40
- User Presets 40
- Press and hold both buttons 42
- IP information 43
- Setting up a DVD source 44
- Specific problems 46
- Chapter Four 48
- Programmer’s Guide 49
- Default address 50
- Programmer’s Guide, cont’d 51
- Picture adjustments 52
- Switcher error responses 54
- Reconfig message may not be 62
- Chapter Five 64
- Switcher Software 65
- Ethernet protocol settings 66
- Switcher Software, cont’d 67
- Installing the software 70
- Using the software 70
- Chapter Six 72
- Ethernet Operation 73
- Ethernet Operation, cont’d 75
- Freezing the output 76
- Outputting a test pattern 76
- Previewing the scan rate 76
- Using Blue-Only mode 76
- Executive mode 76
- Administration fields 78
- ISM IP Settings fields 78
- Input configuration 80
- Output resolution 82
- Output rate 82
- Chapter Seven 84
- Maintenance and Modifications 85
- Switcher 87
- Appendix A 90
- Patch (straight) cable 91
- Crossover cable 91
- Connector 91
- Ethernet Connection, cont’d 93
- Appendix B 96
- Reference Information 97
- Audio input 98
- Audio output 98
- Cables and connectors 100
- Reference Information, cont’d 101
- Extron’s Warranty 104
Related products and manuals for Recording Equipment Extron electronics RGB 112xi
(3 pages)© 2020, manymanuals.com. All rights reserved. | 0.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals