Extron electronics XTP T HDMI User's Guide

User GuideXTP T USW 103XTP SwitcherThree Input Switcher with an Integrated XTP Transmitter68-2292-01 Rev. A07 13

c HDMI connectors — Connect a digital video source device to either or both female HDMI connectors, labeled inputs 2 and 3. They can accept HDMI, DVI,

Making ConnectionsHDMI ConnectionUse an Extron LockIt Lacing Bracket to secure an HDMI cable to each connector as follows:331245Figure 4. Installing

TP Cable Termination and RecommendationsUse the following pin configurations for twisted pair cables.12345678RJ-45ConnectorInsert TwistedPair WiresPin

Contact Closure CommunicationEach port senses an external switch or contact closure. Use these ports to select an input on the switcher. Wire the conn

Power ConnectionApply power to the switcher locally with the provided power supply or remotely with a power injector or a matrix switcher.ATTENTION:

Remote powerThe XTP T USW 103 can be powered remotely through an XTP Power Injector or through an XTP matrix switcher.ATTENTION: XTP remote power is

OperationThis section describes the front panel features of the XTP T USW 103 and provides front panel operations. Topics in this section include:• F

Selecting an InputTo select an input from the front panel, perform the following actions:Press the input selection button that corresponds with the de

Reset ModesUse the recessed Reset button on the rear panel of the switcher to return the device to default settings or to restore factory-shipped firm

SIS Configuration and ControlThe XTP T USW 103 can be configured and controlled using Extron Simple Instruction Set (SIS) commands or the XTP System C

Safety Instructions • EnglishWARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerou

Using the command and response table for SIS commandsThe command and response tables begin on page 15. Figure 11 shows the hexadecimal equivalent of A

Command and Response Tables for SIS CommandsCommand ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionInputsInput selection

Command ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionBlack signal for audio onlyNOTE: The switcher uses a black signa

Command ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionEDIDAssign factory EDIDEAX!*X2$EDID} EdidAX!*X2$]Set the EDID res

XTP System Configuration SoftwareThis section contains installation and configuration procedures for the XTP System Configuration Software for configu

To download the software from the website:Figure 12. Extron Website Download Page1. On the Extron website, click the Download tab.2. From the left

Device SettingsThe Device Settings screen allows a user to view and edit various device settings for the device directly connected to the host device.

Input/Output tabClick the Input/Output tab to open the Input/Output screen. It contains input information, options to apply automatic settings to indi

Analog Video tabClick the Analog Video tab to open the Analog Video screen. It contains signal sampling, image shifting, and saving and recalling inpu

Audio tabClick the Audio tab to open the Audio screen. It contains settings for input format and analog audio gain.Figure 16. Audio TabInput format s

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rule

General tabClick the General tab to open the general screen. It contains settings for executive mode, auto switch mode, and factory reset.Figure 17.

Device Information panelThe Device Information panel displays device information and settings. General Information section Model — Displays the device

Assign EDID1. Select an available EDID setting (represented by a blue, green, or yellow output display icon) from the Available EDID pane.2. Select

Reference InformationThis section contains mounting information and instructions for updating firmware. Topics in this section include:• Mounting• U

Updating Firmware with Firmware LoaderTo upload and update firmware for the XTP T USW 103, download the new firmware to a connected computer and uploa

Downloading FirmwareFigure 20. Downloading Firmware from the Extron Website1. On the Extron website, www.extron.com, click the Download tab.2. On t

Installing Firmware with Firmware Loader1. Connect the host device to the front panel USB port.2. Open Firmware Loader and establish a connection be

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +

Conventions Used in this GuideNotifications The following notifications are used in this guide:WARNING: A warning indicates a situation that has the

ContentsSIS Conguration and Control ... 13Host Device Connection ... 13Simple Instruction Set Control

XTP T USW 103 • Contents v

IntroductionThis section contains general information about this guide and the Extron XTP T USW 103 Universal Switcher with an integrated XTP transmit

Key FeaturesReliable cable infrastructure — Transmits HDMI or digitized analog video, audio, bidirectional RS-232 and IR, and Ethernet up to 330 feet

InstallationThis section contains information for connecting and wiring the XTP T USW 103. Topics in this section include:• Rear Panel Connectors• M