Extron-electronics TLP 1000TV Setup Guide User Manual download pdf

Product Category

IMPORTANT:

Refer to www.extron.com for

the complete TLP 1000 Series

user guide before connecting

the product to the power source.

TLP 1000MV and TLP 1000TV • Setup Guide

Overview

The Extron TLP 1000MV (wall-mounted) and TLP 1000TV (desk-mounted) TouchLink

™

Panels provide simple and versatile

conﬁguration and control for a range of IP Link

control systems. Graphic and text objects are displayed on the screen.

These objects have system control functions associated with them and the touch overlay allows you to activate or regulate

those functions.

These touchpanels communicate through an Ethernet connection to a conﬁgurable IP Link control processor. Video and

audio input is provided by a twisted pair cable connected to an MTP transmitter.

NOTE: The network output must be connected to a network switch, hub, or router that is connected to an Ethernet

LAN or the Internet. An Extron IP Link controller must also be connected to the same network. Suggested

models include IPL T S series (for example, IPL T S4), IPL 250, IPL T CR48, IPL T SFI244, or IPCP 505.

Extron strongly recommends that power is provided by a Power over Ethernet (PoE) power supply.

This guide provides basic instructions for experienced installers to mount and perform initial conﬁguration on the

TLP 1000 series of touchpanels. Full instructions and reference material can be found in the TLP 1000MV and TLP 1000TV

User Guide, which is available on the Extron website (www.extron.com).

Front Panel Features

Extron TLP 1000MV Extron TLP 1000TV

Motion Sensor — when no motion has been detected for a user-deﬁned period of time, the unit goes into sleep

mode. When motion is detected by the sensor, the screen display is restored and active.

Microphone — is located below the LCD screen.

Connection status LED — is unlit during normal operation. The LED blinks red if the connection to the IP Link

controller is lost.

Programmable LEDs — one on each top corner can be programmed to provide system feedback. They light red or

green and can blink or light solid.

LCD screen — has a 1024x600 resolution with a touch overlay. Extron software is used to design and conﬁgure a

graphic user interface to display buttons, text, or icons, which have user-deﬁned functions associated with them.

Speakers — Two speakers placed under the screen, on either side of the panel, provide audible feedback for the user.

Light Sensor — (can only be seen from above the unit) monitors ambient light level and adjusts screen brightness.

1 2 3 4

Summary of Contents

Page 1 - Product Category

1Product CategoryIMPORTANT:Refer to www.extron.com forthe complete TLP 1000 Seriesuser guide before connectingthe product to the power source.TLP 1000

Page 2

2Product Category8109Extron TLP 1000MVUse the Extron pry tool to remove the front faceplate of the TLP 1000MV:h Menu button — activates the on-scree

Page 3 - Mounting Options

3Product CategoryInitial CongurationBefore use, conﬁgure the touchpanel, using the on-screen menus.1. Press the Menu button once. (See “TLP 1000MV

Page 4 - Reset Modes

468-1909-50 Rev. A03 11Extron USA - WestHeadquarters+800.633.9876Inside USA/Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.633.98

Comments to this Manuals

No comments

Extron-electronics TLP 1000TV Setup Guide User Manual

Browse online or download User Manual for Hardware Extron-electronics TLP 1000TV Setup Guide. Extron Electronics TLP 1000TV Setup Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Extron-electronics TLP 1000TV Setup Guide