Extron-electronics USFM 100 Installation imp User Manual download pdf

USFM 100 • Installation Guide

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before starting installation.

When using this accessory, basic precautions should always be followed, including the following:

WARNING: Risk of Personal Injury. Maximum setup load for the USFM 100 (projector arm) is 20 lbs (9.1 kg).

SAVE THESE INSTRUCTIONS

NOTE: Refer to local building standards and codes to verify that the installation will meet the regulatory

requirements. Observe all local and national building and safety codes, UL requirements, and ADA

accessibility guidelines.

WARNING: Risk of Personal Injury and property damage. Do not exceed speciﬁed weight limits of any

component of the installation. Follow the manufacturer's speciﬁcations and installation instructions.

The Extron USFM 100 is a mounting kit for suspending ultra short throw projectors from a wall. The USFM 100 base

plate enclosure is capable of mounting a PoleVault

System switcher and its supplied power supply, with sufﬁcient

room remaining for installing additional devices and cable management. It is designed to be used with the UPB 25

universal projector bracket (supplied with the Extron WallVault

system).

The USFM 100 has knockouts on all four sides that allow external raceways or conduits to be attached for cabling

runs where necessary.

Extron

USFM 100

Plastic Enclosure Cover

Boom Arm

Base Plate

Arm Cover (buttom)

Arm Cover (top)

Arm Cover (front)

Device Mounting Plate

Figure 1. USFM 100 Parts

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - IMPORTANT SAFETY INSTRUCTIONS

1USFM 100 • Installation GuideIMPORTANT SAFETY INSTRUCTIONSRead all instructions before starting installation.When using this accessory, basic precaut

Page 2 - Installation

2Hardware Included in the KitParts Qty Application¼ - 20 x 2 inch, pan head bolts, 4 Base plate to wall installation¼ inch Toggle assembly 4 Base pla

Page 3 - 2. Mount the Switcher

3LevelCutout forSignal CableAccessMarker for Pilot HoleUSFM 100Base PlateMountingHolesSignal CablesExiting fromCutoutFigure 2. Wall Mounting Featuresc

Page 4 - 3. Run Cables

4NOTE: Mount the switcher with the rear panel uppermost for ease of cable connection (see ﬁgure 4).(1) 6-32 x 1/4" Screw(2) 4-40 x 1/4" Scr

Page 5 - 4. Cable the Switcher

5Signal Cable AccessCutout Option2400V700Raceway OptionConduit OptionFigure 5. Cabling Run OptionsIf running cable behind the walls:Run all the cables

Page 6 - OR SHORT

65. Attach the Boom Arm, Power Supply, and Projectora. Hook the boom arm over the top rail on the base plate so that the tab on the arm (see ﬁgure 6,

Page 7 - USFM 100 Dimensions

734.40"(87.38 cm)2.20"(5.59 cm)31.80"(80.77 cm)3.60"(9.14 cm)3.85"(9.77 cm)11.82"(30.02 cm)1.25"(3.18 cm)Base Plate

Page 8 - Aligning the Projector

8USFM 100 Installation Guide, cont'd68-1838-01 Rev C08 1231.80" (max)(80.77 cm)30.00" (max)(76.20 cm)3.71"(9.42 cm)3.22” - 5.22&qu

Comments to this Manuals

No comments

Extron-electronics USFM 100 Installation imp User Manual

Browse online or download User Manual for Hardware Extron-electronics USFM 100 Installation imp. Extron Electronics USFM 100 Installation imp User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Extron-electronics USFM 100 Installation imp