Extron-electronics ISM 482 User Manual Page 11
- Page / 82
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ISM 482 Integrated Scaling Matrix Switcher • Installation 5
Installation
This section describes:
• Mounting the Switcher
• Cabling and Rear Panel Views
• Configuration
Mounting the Switcher
Four uninstalled rubber feet are included with the switcher. If you are going to rack mount
the switcher, mount it before you cable it (see “Rack Mounting,” below), and do not install
the rubber feet. If you are not rack mounting the switcher, see “Tabletop Pacement,” below.
Tabletop Placement
For tabletop placement, install the self-adhesive rubber feet/pads (provided) onto the four
corners of the bottom of the switcher.
Rack Mounting
UL guidelines
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
switcher into a rack (see figure 2 on the next page).
• Elevated operating ambient temperature — If the equipment is installed in a closed
or multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, install the switcher in an
environment compatible with the maximum ambient temperature (Tma = +122 °F,
+50°C) specified by Extron.
• Reduced air flow — Install the equipment in a rack so that the amount of air flow
required for safe operation of the equipment is not compromised.
• Mechanical loading — Mount the equipment in the rack so that a hazardous
condition is not achieved due to uneven mechanical loading.
• Circuit overloading — Connect the equipment to the supply circuit and consider the
effect that circuit overloading might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when
addressing this concern.
• Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct connections
to the branch circuit (that is, use of power strips).
Mounting instructions
To rack mount the switcher, use two screws on each end of the switcher to attach the
switcher to the rack (see figure 2).
- User Guide 1
- No Photo 1
- Available yet 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 3
- Software Commands 4
- Contents 5
- Introduction 7
- Network/ 8
- Internet 8
- Features 9
- Installation 11
- Input Connections 12
- RCA Connector 13
- 3.5 mm Stereo Plug Connector 13
- Standard Output Connections 14
- Ethernet Connection 15
- Optional Output Connection 15
- Configuration 16
- Operation 17
- Output Buttons and LEDs 18
- Selecting an input 19
- Recalling a user preset 19
- Black/Mute Button and LEDs 20
- Picture Adjustment Buttons 20
- Front Panel Operations 21
- Menu System Overview 22
- Input Configuration submenu 23
- Output Configuration menu 24
- Output Resolution submenu 24
- Advanced Configuration Menu 26
- Test Pattern submenu 27
- Blanking submenu 27
- RGB Delay submenu 27
- Enhanced Mode submenu 28
- Pixel Phase submenu 28
- PAL Film Mode submenu 28
- Reset submenu 28
- User Presets menu 29
- Save Preset submenu 29
- Erase Preset submenu 30
- Exit menu 30
- Picture Adjustments 31
- Press and hold both buttons 32
- IP Information 33
- Optimizing the Video 34
- Optimizing the Audio 35
- Troubleshooting 35
- General Checks 36
- Specific Problems 36
- Programming Guide 37
- Ethernet Link 38
- } character) 39
- Switcher-Initiated Messages 40
- Host-to-Switcher Instructions 43
- Switcher Error Responses 43
- Command Function 44
- SIS Command 44
- Response 44
- Additional description 44
- Symbol definitions 50
- Command and response table 50
- Switcher Software 53
- Ethernet protocol settings 54
- Using the Control Program 55
- Button-Label Generator 57
- Using the Software 58
- HTML Operation 59
- Control Page 61
- Freezing the Output 62
- Outputting a Test Pattern 62
- Previewing the Scan Rate 62
- Using Blue-Only Mode 62
- Executive Mode 62
- System Configuration Page 63
- ISM IP Settings Fields 64
- File Management Page 65
- I/O Configuration Page 66
- Output resolution 68
- Output rate 68
- Output format 68
- Output polarity 69
- Maintenance and 70
- Modifications 70
- Switcher 71
- Installing a Firmware Upgrade 72
- Installing a DVI Output Card 73
- Determining Default Addresses 76
- Connecting as a Telnet Client 77
- Reference 79
- Information 79
- Button Labels 80
- Extron Warranty 82
Related products and manuals for Accessories for video Extron-electronics ISM 482
(9 pages)© 2020, manymanuals.com. All rights reserved. | 2.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals