Extron-electronics ISM 482 User Manual Page 76
- Page / 82
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ISM 482 Integrated Scaling Matrix Switcher • Ethernet Connection 70
Determining Default Addresses
To access the ISM switcher via the Ethernet port, you need the Extron ISM IP address. If the
address has been changed to an address comprised of words and characters, the actual
numeric IP address can be determined using the Ping utility. If the address has not been
changed, the factory-specified default is 192.168.254.254.
Ping can also be used to test the Ethernet link to the ISM.
Pinging to Determine the Switcher IP Address
The Microsoft Ping utility is available at the DOS prompt. Ping tests the Ethernet interface
between the computer and the ISM. Ping can also be used to determine the actual numeric
IP address from an alias and to determine the Web address.
Access the DOS prompt and ping the switcher as follows:
1. Click Start > Run.
2. At the Open prompt, type command.
3. Click the OK button.
4. At the DOS prompt, type ping {IP address} and press the keyboard Enter key (
Enter
).
The computer returns a display similar to figure 54.
The line Pinging ... reports the actual numeric IP address, regardless of whether you
entered the actual numeric IP address or an alias name.
C:\>ping 192.168.254.254
Pinging 192.168.254.254 with 32 bytes of data:
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Ping statistics for 192.168.254.254:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Figure 54. Ping Response
Pinging to Determine the Web IP Address
The Ping utility has a modifier, -a, that directs the command to return the Web address
rather than the numeric IP address.
At the DOS prompt, type ping -a {IP address} and then press
Enter
. The computer’s
return display is similar to the Ping response shown in figure 54, except that when you
specify the -a modifier, the line Pinging mail... reports the Web IP address rather than the
numeric IP address, regardless of whether you entered the actual numeric IP address or an
alias name.
- User Guide 1
- No Photo 1
- Available yet 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 3
- Software Commands 4
- Contents 5
- Introduction 7
- Network/ 8
- Internet 8
- Features 9
- Installation 11
- Input Connections 12
- RCA Connector 13
- 3.5 mm Stereo Plug Connector 13
- Standard Output Connections 14
- Ethernet Connection 15
- Optional Output Connection 15
- Configuration 16
- Operation 17
- Output Buttons and LEDs 18
- Selecting an input 19
- Recalling a user preset 19
- Black/Mute Button and LEDs 20
- Picture Adjustment Buttons 20
- Front Panel Operations 21
- Menu System Overview 22
- Input Configuration submenu 23
- Output Configuration menu 24
- Output Resolution submenu 24
- Advanced Configuration Menu 26
- Test Pattern submenu 27
- Blanking submenu 27
- RGB Delay submenu 27
- Enhanced Mode submenu 28
- Pixel Phase submenu 28
- PAL Film Mode submenu 28
- Reset submenu 28
- User Presets menu 29
- Save Preset submenu 29
- Erase Preset submenu 30
- Exit menu 30
- Picture Adjustments 31
- Press and hold both buttons 32
- IP Information 33
- Optimizing the Video 34
- Optimizing the Audio 35
- Troubleshooting 35
- General Checks 36
- Specific Problems 36
- Programming Guide 37
- Ethernet Link 38
- } character) 39
- Switcher-Initiated Messages 40
- Host-to-Switcher Instructions 43
- Switcher Error Responses 43
- Command Function 44
- SIS Command 44
- Response 44
- Additional description 44
- Symbol definitions 50
- Command and response table 50
- Switcher Software 53
- Ethernet protocol settings 54
- Using the Control Program 55
- Button-Label Generator 57
- Using the Software 58
- HTML Operation 59
- Control Page 61
- Freezing the Output 62
- Outputting a Test Pattern 62
- Previewing the Scan Rate 62
- Using Blue-Only Mode 62
- Executive Mode 62
- System Configuration Page 63
- ISM IP Settings Fields 64
- File Management Page 65
- I/O Configuration Page 66
- Output resolution 68
- Output rate 68
- Output format 68
- Output polarity 69
- Maintenance and 70
- Modifications 70
- Switcher 71
- Installing a Firmware Upgrade 72
- Installing a DVI Output Card 73
- Determining Default Addresses 76
- Connecting as a Telnet Client 77
- Reference 79
- Information 79
- Button Labels 80
- Extron Warranty 82
Related products and manuals for Accessories for video Extron-electronics ISM 482
(9 pages)© 2020, manymanuals.com. All rights reserved. | 0.759 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals