Extron-electronics TLE 710 Setup Guide User Manual download pdf

Before connecting the TLP 710CV to a

power source, refer to the TLP 710CV user

guide, which is available at

www.extron.com.

TLP 710CV and TLE 710 • Setup Guide

Overview

The Extron TLP 710CV 7-inch Cable Cubby

TouchLink

™

touchpanel and TLE 710 enclosure provide AV connectivity using

convenient pullout cables. The TLP 710CV also provides simple and versatile conguration and control for a range of IPLink

control systems using a touch screen. The touchpanel communicates through an Ethernet connection to a congurable IP Link

control processor. Video and audio input is provided by a twisted pair cable connected to an MTP transmitter.

NOTE: The network output must connect via a network switch, hub, or router to an Ethernet LAN or the Internet, with

an Extron IP Link controller on the same network. Suggested controllers include IPL T S series (for example, IPL T S4),

IPL250, IPL T CR48, IPLTSFI244, or IPCP series.

The rst four pages of this guide provides basic instructions for experienced installers to mount either the TLP 710CV or the

TLE710. The last four pages show initial conguration for the TLP710CV. For reference material and full instructions about

conguring the touchpanel, see the TLP 710CV User Guide (see www.extron.com).

Planning

 Before making any cuts, select the best location for the

TLP710CV or TLE 710.

 Ensure that the edge that opens on the lid is oriented correctly.

 Ensure there is enough space for all the system cables and

components, including cable retractors, if they are to be

installed.

 Decide on the method for cutting a hole in the table:

z Hand router and template

z CNC wood router

z Jigsaw and paper template

 Verify that you have the correct template or dimensions.

 Check all relevant regulations.

z Ensure the installation complies with local, state, and

national building and electrical codes.

z Ensure the installation complies with the Americans with

Disabilities Act or other accessibility requirements.

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

Vacuum Cleaner

1/4" Hex Nut Driver

Marking Pen

Square

Included Parts

With Power

Module

Without Power

Module

AC Power Module* 1 0

Pass-through AAPs

†

3 3

Blank AAPs 6 6

1-space bracket kit 0 1

2-space bracket kit 3 4

3-space bracket kit 1 1

NOTES:

* Inside the US, the TLP 710CV may be purchased with or without an AC power module. If required, a power module for

the TLE 710 must be purchased separately. Outside the US, see www.extron.com to find an AC power module for

your country.

†

Active or Passive AAPs must be purchased separately (see www.extron.com).

‡

The Power over Ethernet injector is provided only with the TLP 710CV.

Table Clamps

Extron

Removal Tool

Zip Ties

#4−40 Screws

and Nuts

AC Power Module*

Blank AAPs

Pass-thru AAPs

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

PWR LAN OUT

LAN-IN

AMBER

GREEN

BLINK

POWER ON

POWER ACTIVE

LOAD ERROR

Power over Ethernet

(PoE) Injector

‡

(TLP 710CV only)

TLP 710CV or TLE 710

Extron

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Included Parts

1Before connecting the TLP 710CV to a power source, refer to the TLP 710CV user guide, which is available at www.extron.com.TLP 710CV and TLE 710 • Se

Page 2 - Step 2 — Cut the Surface

2TLP 710CV and TLE 710 • Setup Guide (Continued)2Mounting the TLP 710CV and TLE 710Step 1 — Obtain Cut-out DimensionsATTENTION: • The table should b

Page 3 - Step 6 — AAP Assembly

3Step 3 — Run all CablesRun all cables necessary to support the AC connector, the cables stored in the cubby, and all planned AAP connectors. Run the

Page 4 - COMPUTER

4TLP 710CV and TLE 710 • Setup Guide (Continued)4Step 7 — Install the AAP Assembly1. From under the table, push the rst AAP assembly through the bo

Page 5 - (5 mm) Max

5Connecting the TLP 710CVNOTE: The rest of this guide applies only to the TLP 710CV (not to the TLE 710).The cable connections are located in a panel

Page 6

6TLP 710CV and TLE 710 • Setup Guide (Continued)Step 12 — Power on the TLP 710CV for the First TimePower on all the devices connected to the TLP710C

Page 7 - Initial Conguration

7Initial CongurationBefore use, congure the touchpanel, using the on-screen menus.1. Remove the bezel, using the Extron removal tool.2. Press the

Page 8 - GUI Design and Conguration

868-2117-50 Rev. D 04 13Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.

Comments to this Manuals

No comments

Extron-electronics TLE 710 Setup Guide User Manual

Browse online or download User Manual for Hardware Extron-electronics TLE 710 Setup Guide. Extron Electronics TLE 710 Setup Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Extron-electronics TLE 710 Setup Guide