Extron-electronics DMS 1600_2000_3200_3600 User Guide User Manual Page 107
- Page / 121
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
DMS 1600, DMS 2000, DMS 3200, and DMS 3600 • Maintenance and Modifications 101
Removing and Installing the I/O Board or Blank Panel
NOTE: For proper cooling and air flow, install boards or blank panels in all locations.
Figure 67 shows a mix of I/O boards. On the boards, the input and output DVI connectors
are identified as A through D. Each I/O board is identified by the input and output numbers
supported by the board position (1 - 4, 5 - 8, and so on).
ANAHEIM, CA
100-240V 50/60Hz 1.2A MAX.
PRIMARY POWER SUPPLY
REDUNDANT POWER SUPPLY
1 - 4
5 - 8
9 - 12
13 - 16
A B
DVI-D INPUTS DVI-D OUTPUTS
C D A B C D
DVI-D OUTPUTS
ABCD
AB
TMDS
FIBER
INPUTS
CDAB
TMDS
FIBER
OUTPUTS
DMS FIBER 44
CD
Location A
Input
Location D
Output
Location D
Output
Location A
Input
Input 1
Slot 1
(1-4) Input/Output
Board
Slot 2
(5-8) Input/Output
Board
Slot 4
No board installed
Slot 3
(9-12) Output Boa
rd
Input 2 Input 3 Input 4
Input 5 Input 6Input 7Input 8
Output 9
Output 10
Output 11
Output 12
Output 1
Output 2 Output 3 Output 4
Figure 67. Arrangement of Inputs and Outputs on the I/O Boards
Slot Inputs and outputs Slot Inputs and outputs
1 1 through 4 5* 17 through 20
2 5 through 8
6
21 through 24
3 9 through 12
7
25 through 28
4 13 through 16
8
29 through 32
9
33 through 36
* DMS 2000, DMS 3200, and DMS 3600 only
DMS 3200 and DMS 3600 only
DMS 3600 only
Locations A through D correspond to the input and output numbers identified by the board
position numbers. (For example, the input and output numbers supported by the I/O board
in slot 2 (location 5 - 8) are as follows: A = 5, B = 6, C = 7, and D = 8.) Inputs and outputs
are grouped separately, with inputs A through D on the left and outputs A through D on the
right.
Below are installation guidelines for the switcher configuration; if you incorrectly order the
I/O boards, the switcher will not recognize some inputs, outputs, or both.
• You must install a 4x4 DVI or fiber optic input and output board in the top slot (slot 1).
• You can install any of the six board types (a 4x4 DVI or fiber optic input and output
board, a 4 DVI or fiber optic input board, or a 4 DVI or fiber optic output board) or a
blank panel in the next slot (slot 2).
• You can install any of the board types in the slot directly underneath a 4x4 input and
output board.
• After you install a 4-input board or 4-output board, all active boards underneath it must
be the same size (4-input or 4-output).
• Within these size guidelines (4-input must follow 4-input or 4-output must follow
4-output), you can follow a DVI board with a fiber optic board or follow a fiber optic
board with a DVI board.
• If you install a blank panel, all slots under it must contain blank panels (you cannot skip
a slot).
- User Guide 1
- DMS 1600, DMS 2000 1
- DMS 3200, and DMS 3600 1
- Safety Instructions 2
- FCC Class A Notice 3
- FDA/IEC 60825-1 Requirements 3
- Specifications Availability 4
- Contents 5
- Introduction 7
- DMS 3600 8
- Features 9
- Installation 12
- I/O Boards 15
- I/O connections 16
- Remote Port 17
- Ethernet Port 17
- Reset Button and LED 18
- DMS 2000 19
- Operation 20
- Input and Output Buttons 22
- Control Buttons 24
- Power Indicators 25
- 29 28 30 31 26
- Front Panel Operations 27
- Creating a Configuration 28
- 1 2 3 4 5 6 7 8 15 16 29
- 1 2 3 4 5 6 7 8 32
- I/O Grouping 33
- 1324Group # 34
- Press the button 40
- Background Illumination 41
- Rear Panel Operations 42
- • clears all output mutes 43
- • clears all I/O grouping 43
- Troubleshooting 45
- Digital Signal Guidelines 46
- Configuration Worksheets 47
- • Tied to the VCR (output 6) 48
- Input sources 49
- Preset # Title: 49
- 10 11 12 13 14 15 16123456789 49
- Output destinations 49
- Preset # 50
- Programming Guide 52
- Ethernet (LAN) Port 53
- Host-to-Switcher Instructions 54
- Switcher-Initiated Messages 54
- Switcher Error Responses 55
- Command ASCII Command 57
- Response 57
- Additional Description 57
- Additional description 65
- Matrix Software 67
- Starting the program 70
- Using the program 71
- IP Settings/Options Window 73
- Hardware Address field 74
- Use DHCP checkbox 74
- Sync Time to PC button 75
- Use Daylight Saving checkbox 75
- E-mail Addressee fields 77
- Updating Firmware 78
- Tools > Update firmware 80
- OK to continue 80
- Uploading HTML Files 82
- Windows Menus 83
- Tools menu 84
- Proper operation 85
- Component has failed 85
- Preferences menu 86
- Master-Reset selection 87
- Using Emulation Mode 88
- Using the Help System 88
- HTML Operation 91
- Status Tab 93
- Configuration Tab 95
- Date/Time Settings fields 97
- Passwords Page 98
- Email Settings Page 99
- Firmware Upgrade Page 100
- File Management Tab 102
- Control Tab 103
- EDID and Mute Settings Page 104
- Special Characters 105
- Modifications 106
- Maintenance and 106
- PRIMARY POWER SUPPLY 107
- REDUNDANT POWER SUPPLY 107
- (DMS 1600 and DMS 3600) 109
- Removing a Fan Module 110
- Installing a Fan Module 111
- Ethernet Connection 114
- Microsoft Telnet> 117
- Subnetting — A Primer 119
- Extron Warranty 121
Related products and manuals for Accessories for video Extron-electronics DMS 1600_2000_3200_3600 User Guide
(2 pages)© 2020, manymanuals.com. All rights reserved. | 2.530 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals