Extron-electronics VN-Matrix 200 Series User Manual Page 17
- Page / 123
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rack Mounting
Always use the special under-desk mounting kits (optional) to secure the VNC 200. See
“Optional Accessories” for the under-desk mounting kit. Full details on using the kit are
included with each kit. It will be necessary to remove the four feet prior to rack mounting.
Never place other units directly on top of the VNC 200 when it is rack-mounted as this will
place excessive strain on the mounting brackets.
Under-desk Mounting
Always use the special under-desk mounting kit (optional) to secure the VNC 200. See
“Optional Accessories” for the under-desk mounting kit. Full details on using the kit are
included with each kit.
Power Connection via PSU
Always ensure that the power supply is the correct voltage and frequency for all
equipment within the rack, and that it has a good ground (earth) connection.
Where a power strip is used, always ensure that the current rating of both the power strip
and the supply is sufficient for all equipment within the rack.
The VNC 200 must be powered from a 12 VDC regulated supply. A suitable power supply
unit (PSU) is provided. The power connection details that follow relate to the PSU.
CAUTION:
• Never connect the VNC 200 directly to the power source.
• To ensure CE compliance always use the PSU provided.
• If a backup or replacement PSU is required, always use an Extron approved
PSU.
Supply Requirements for PSU
CAUTION: Always observe the following instructions to ensure safe and reliable
operation of the PSU.
Always ensure that the supply voltage is single phase only and is within the permitted
range:
100 – 240 VAC (0.45 A Max.) 50 – 60 Hz.
NEVER connect the PSU to a DC supply.
DO NOT allow the power outlet to be overloaded. This is particularly important to check
when powering several items of equipment from a single power outlet (that is, within
rack-mounted installations).
WARNING:
• This equipment must be grounded.
• To avoid the possible risk of electric shock or product damage due to con-
densation, ALWAYS allow the PSU to adapt to the ambient temperature and
humidity for at least thirty minutes BEFORE switching on. This is particularly
important when moving the unit from a cold location to a warm location.
VN-Matrix 200 Series • Installation 12
- User Guide 1
- VN-Matrix 1
- 200 Series: 1
- VNC 200 DVI, VNE 200 DVI, and 1
- VND 200 DVI 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- Copyright 3
- Trademarks 3
- Contents 4
- Introduction 6
- Firmware Version 7
- Product Range 7
- Functional Overview 8
- Decoder Display Capability 9
- Control Capability 9
- Network Requirements 9
- Example System Application 10
- Data Transport Methods 10
- SOURCE DISPLAY 11
- SOURCE DISPLA 12
- VN-MATRIX 200 SERIES 13
- RGB/DVI OVER IP 13
- Rear Panel Features 14
- Installation 15
- Procedure 15
- Mounting Requirements 16
- Power Connection via PSU 17
- Power Cord for PSU 18
- External Supply Protection 19
- Network Communications Setup 20
- To access the setup menus… 21
- Connect Devices 24
- Connecting a digital source 25
- SOURCE COMPUTER 26
- Connecting a digital display 27
- Connecting an analog display 28
- Device List Page 31
- Save All tab 32
- Additional Setup for Audio 35
- EDID options 36
- Identify Mode 36
- Audio status 37
- Advanced setup options 38
- Help tab for details 39
- Help tab 39
- Save All tab as shown above 40
- Identify mode 41
- Nodata Splash Mode 43
- Device mode 44
- Troubleshooting 45
- Source Checkup 47
- System Checkup 48
- Controller Checkup 49
- Serial Transport 50
- TCP RS-232RS-232 TCP 51
- Serial / Telnet Commands 52
- Device Commands 53
- Data Stream Mode 54
- Remote Keyboard 56
- Operation 56
- Mouse and Keyboard Control 57
- Mode = Enable 59
- Advanced Setup 60
- Procedures 60
- Video Setup Page 61
- Custom Input Modes 63
- Configure tab 64
- Creating a custom input mode 65
- VideoPort icon b 67
- Video Setup tab c 67
- Bandwidth (Source) Page 69
- Figure 45. Bandwidth Page 70
- Bandwidth Management 71
- Setting the maximum bit rate 72
- Setting the video quality 72
- Transform setting 73
- Quality Control settings 74
- Temporal compression setting 74
- Monitoring the bit rate 75
- Audio Compression 76
- Decoder Set Up 77
- Adjusting the Playback Delay 79
- Custom Output Modes 80
- Creating a CVT output mode 81
- Creating a custom output mode 81
- Parameter Meaning 82
- Controller Configuration 84
- Controller Licensing 85
- Upgrading Device Firmware 85
- Changing a Device Licence 88
- Update Licence button 89
- Alarms and SNMP 90
- Alarms Page 91
- Apply Filter Change 92
- Save All tab is used to make 92
- Alarms tab is selected 92
- Alarm Logs 93
- Overview – SNMP 96
- SNMP Trap Destinations 97
- IP Addressing 98
- Choosing IP Addresses 99
- Subnet Mask 100
- Response Messages 100
- Understanding 102
- Network 102
- Performance 102
- Nodes, Switchers, and Routers 103
- Protocols 103
- Browser 106
- Configuration 106
- To enable JavaScript: 107
- Mozilla (v1.3 or Above) 108
- Technical Data 110
- DVI Input (IN) 111
- DVI Output (OUT/LOOP) 113
- Network (1 and 2) 115
- RS-232 Port Settings 116
- Serial Port Login Procedure 117
- Command options 117
- Starting Telnet 118
- Login Procedure 118
- Reference 119
- Information 119
- Accessories 122
- Extron® Warranty 123
- Warranty 123
Related products and manuals for Accessories for video Extron-electronics VN-Matrix 200 Series
(138 pages)© 2020, manymanuals.com. All rights reserved. | 1.861 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals