Extron-electronics VN-Matrix 200 Series User Manual Page 38
- Page / 123
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced setup options
The encoder set up procedure on the preceding pages will achieve a basic level of
operation which will be adequate for most normal applications.
The following advanced setup options are possible.
Fine-tuning of input parameters See “Fine-tuning a Source (Manual
Overrides)”
Creation of custom input modes See “Creating a custom input mode”
Changing video compression See “Managing Compression and
Bandwidth Settings”
Managing bandwidth usage See “Bandwidth Management Settings”
Changing audio compression See “Audio Compression”
Configuring a VNC 200 as a Decoder (Display)
The following procedure assumes that at least one VNC 200 encoder has been configured
and is ready to stream a source (see “Configuring a VNC 200 as an Encoder (Source).”
It is also assumed that a suitable display device is connected to the VNC 200. For details
on how to connect a display, see “Setup Connection Procedure.”
NOTE: This procedure provides a basic level of configuration which will be adequate
for most systems. For additional advanced setup options, see “Additional
Information for Decoder Setup”.
Figure 26. Configuring a VNC 200 as a Decoder
a On the Device List page click the device that you want to configure as shown in the
above image. The Device page will then appear.
VN-Matrix 200 Series • System Configuration 33
- User Guide 1
- VN-Matrix 1
- 200 Series: 1
- VNC 200 DVI, VNE 200 DVI, and 1
- VND 200 DVI 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- Copyright 3
- Trademarks 3
- Contents 4
- Introduction 6
- Firmware Version 7
- Product Range 7
- Functional Overview 8
- Decoder Display Capability 9
- Control Capability 9
- Network Requirements 9
- Example System Application 10
- Data Transport Methods 10
- SOURCE DISPLAY 11
- SOURCE DISPLA 12
- VN-MATRIX 200 SERIES 13
- RGB/DVI OVER IP 13
- Rear Panel Features 14
- Installation 15
- Procedure 15
- Mounting Requirements 16
- Power Connection via PSU 17
- Power Cord for PSU 18
- External Supply Protection 19
- Network Communications Setup 20
- To access the setup menus… 21
- Connect Devices 24
- Connecting a digital source 25
- SOURCE COMPUTER 26
- Connecting a digital display 27
- Connecting an analog display 28
- Device List Page 31
- Save All tab 32
- Additional Setup for Audio 35
- EDID options 36
- Identify Mode 36
- Audio status 37
- Advanced setup options 38
- Help tab for details 39
- Help tab 39
- Save All tab as shown above 40
- Identify mode 41
- Nodata Splash Mode 43
- Device mode 44
- Troubleshooting 45
- Source Checkup 47
- System Checkup 48
- Controller Checkup 49
- Serial Transport 50
- TCP RS-232RS-232 TCP 51
- Serial / Telnet Commands 52
- Device Commands 53
- Data Stream Mode 54
- Remote Keyboard 56
- Operation 56
- Mouse and Keyboard Control 57
- Mode = Enable 59
- Advanced Setup 60
- Procedures 60
- Video Setup Page 61
- Custom Input Modes 63
- Configure tab 64
- Creating a custom input mode 65
- VideoPort icon b 67
- Video Setup tab c 67
- Bandwidth (Source) Page 69
- Figure 45. Bandwidth Page 70
- Bandwidth Management 71
- Setting the maximum bit rate 72
- Setting the video quality 72
- Transform setting 73
- Quality Control settings 74
- Temporal compression setting 74
- Monitoring the bit rate 75
- Audio Compression 76
- Decoder Set Up 77
- Adjusting the Playback Delay 79
- Custom Output Modes 80
- Creating a CVT output mode 81
- Creating a custom output mode 81
- Parameter Meaning 82
- Controller Configuration 84
- Controller Licensing 85
- Upgrading Device Firmware 85
- Changing a Device Licence 88
- Update Licence button 89
- Alarms and SNMP 90
- Alarms Page 91
- Apply Filter Change 92
- Save All tab is used to make 92
- Alarms tab is selected 92
- Alarm Logs 93
- Overview – SNMP 96
- SNMP Trap Destinations 97
- IP Addressing 98
- Choosing IP Addresses 99
- Subnet Mask 100
- Response Messages 100
- Understanding 102
- Network 102
- Performance 102
- Nodes, Switchers, and Routers 103
- Protocols 103
- Browser 106
- Configuration 106
- To enable JavaScript: 107
- Mozilla (v1.3 or Above) 108
- Technical Data 110
- DVI Input (IN) 111
- DVI Output (OUT/LOOP) 113
- Network (1 and 2) 115
- RS-232 Port Settings 116
- Serial Port Login Procedure 117
- Command options 117
- Starting Telnet 118
- Login Procedure 118
- Reference 119
- Information 119
- Accessories 122
- Extron® Warranty 123
- Warranty 123
Related products and manuals for Accessories for video Extron-electronics VN-Matrix 200 Series
(138 pages)© 2020, manymanuals.com. All rights reserved. | 1.515 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals