Extron-electronics VN-Matrix 200 Series User Manual Page 32
- Page / 123
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Interface timeout and logging out
If the web interface is left unattended or is not used for a period of 30 minutes it will
automatically logout. You can start using the interface again by re-entering your login
details.
To logout of the web interface…
Click the Logout tab on any page or close the web browser.
Save All tab
On the Device List page only, there is a Save All tab.
Clicking the Save All tab will save all current settings (including those that have been
updated) for all VNC 200 units.
Configuring a VNC 200 as an Encoder (Source)
The following procedure assumes that a valid source is connected to the VNC 200. For
details on how to connect a source, see “Setup and Connection Procedure”.
NOTE: This procedure provides a basic level of configuration which will be
adequate for most systems. For additional options, see “Advanced Setup
Procedures.”
Figure 17. Configuring a VNC 200 as an Encoder
a On the Device List page, click the device that you want to configure. The Device page
will appear.
b If the device has not been configured (Device Type is none), click the create source
button (see Device Setup Mode on the Help tab).
TIP: You can change the default device name to be more relevant to the source
input (for example, Camera1). See Ç below.
VN-Matrix 200 Series • System Configuration 27
- User Guide 1
- VN-Matrix 1
- 200 Series: 1
- VNC 200 DVI, VNE 200 DVI, and 1
- VND 200 DVI 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- Copyright 3
- Trademarks 3
- Contents 4
- Introduction 6
- Firmware Version 7
- Product Range 7
- Functional Overview 8
- Decoder Display Capability 9
- Control Capability 9
- Network Requirements 9
- Example System Application 10
- Data Transport Methods 10
- SOURCE DISPLAY 11
- SOURCE DISPLA 12
- VN-MATRIX 200 SERIES 13
- RGB/DVI OVER IP 13
- Rear Panel Features 14
- Installation 15
- Procedure 15
- Mounting Requirements 16
- Power Connection via PSU 17
- Power Cord for PSU 18
- External Supply Protection 19
- Network Communications Setup 20
- To access the setup menus… 21
- Connect Devices 24
- Connecting a digital source 25
- SOURCE COMPUTER 26
- Connecting a digital display 27
- Connecting an analog display 28
- Device List Page 31
- Save All tab 32
- Additional Setup for Audio 35
- EDID options 36
- Identify Mode 36
- Audio status 37
- Advanced setup options 38
- Help tab for details 39
- Help tab 39
- Save All tab as shown above 40
- Identify mode 41
- Nodata Splash Mode 43
- Device mode 44
- Troubleshooting 45
- Source Checkup 47
- System Checkup 48
- Controller Checkup 49
- Serial Transport 50
- TCP RS-232RS-232 TCP 51
- Serial / Telnet Commands 52
- Device Commands 53
- Data Stream Mode 54
- Remote Keyboard 56
- Operation 56
- Mouse and Keyboard Control 57
- Mode = Enable 59
- Advanced Setup 60
- Procedures 60
- Video Setup Page 61
- Custom Input Modes 63
- Configure tab 64
- Creating a custom input mode 65
- VideoPort icon b 67
- Video Setup tab c 67
- Bandwidth (Source) Page 69
- Figure 45. Bandwidth Page 70
- Bandwidth Management 71
- Setting the maximum bit rate 72
- Setting the video quality 72
- Transform setting 73
- Quality Control settings 74
- Temporal compression setting 74
- Monitoring the bit rate 75
- Audio Compression 76
- Decoder Set Up 77
- Adjusting the Playback Delay 79
- Custom Output Modes 80
- Creating a CVT output mode 81
- Creating a custom output mode 81
- Parameter Meaning 82
- Controller Configuration 84
- Controller Licensing 85
- Upgrading Device Firmware 85
- Changing a Device Licence 88
- Update Licence button 89
- Alarms and SNMP 90
- Alarms Page 91
- Apply Filter Change 92
- Save All tab is used to make 92
- Alarms tab is selected 92
- Alarm Logs 93
- Overview – SNMP 96
- SNMP Trap Destinations 97
- IP Addressing 98
- Choosing IP Addresses 99
- Subnet Mask 100
- Response Messages 100
- Understanding 102
- Network 102
- Performance 102
- Nodes, Switchers, and Routers 103
- Protocols 103
- Browser 106
- Configuration 106
- To enable JavaScript: 107
- Mozilla (v1.3 or Above) 108
- Technical Data 110
- DVI Input (IN) 111
- DVI Output (OUT/LOOP) 113
- Network (1 and 2) 115
- RS-232 Port Settings 116
- Serial Port Login Procedure 117
- Command options 117
- Starting Telnet 118
- Login Procedure 118
- Reference 119
- Information 119
- Accessories 122
- Extron® Warranty 123
- Warranty 123
Related products and manuals for Accessories for video Extron-electronics VN-Matrix 200 Series
(138 pages)© 2020, manymanuals.com. All rights reserved. | 0.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals