Extron-electronics VN-Matrix 200 Series User Manual Page 53
- Page / 123
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Device Commands
mode <deviceid> <state>
Changes the operating mode of the specified device.
<deviceid> Is the device serial number of the device or the user-defined device name.
<state> Is the required mode and can be set to:
•enable–fornormaloperation
•disable–tostopencodersourcestreamingorstopdisplayoutputonadecoder
•standby–tostopencodersourcestreamingordisplaysplashscreenonadecoder
Example: mode 16 enable
channel <deviceid> <window> <sourceid.videoport.protocol>
Changes the source being displayed in a window of the specified decoder device.
<deviceid> Is the device serial number of the device or the user-defined device name.
<window> Is the window object number. Currently this can only be 0.
<sourceid.videoport.protocol> Is the source to be displayed, where:
•sourceidistheserialnumberofthesourcedevice
•videoportisthevideoinputnumber,usuallysetto0
•protocolspecifieseitherRTPorTCP,setto0forRTPor1forTCP
Note: Full stops (.) are required between the sourceid, videoport, and protocol values.
Example: channel 17 0 16.0.1
optimization <deviceid> <videoport> <mode>
Changes the compression transform for the specified encoder device.
<deviceid> Is the device serial number of the device or the user-defined device name.
<videoport> Is the video input number, usually set to 0.
<mode> Is the source transform to be used and can be set to:
•video–forvideosources
•graphics–forgraphicssources
Example: optimization 16 0 video
bandwidth <deviceid> <videoport> <bandwidth>
Changes the target bandwidth value for the specified encoder device.
<deviceid> Is the device serial number of the device or the user-defined device name.
<videoport> Is the video input number, usually set to 0.
<bandwidth> Is the bandwidth value in megabits per second.
Example: bandwidth 16 0 5
Response Messages
All commands (except for user and exit) will generate an OK response message if the
command is successfully executed.
Unrecognized commands or invalid command parameters will generate an error message
in the format
fail: followed by a brief description of the error, for example fail:
unknown command
.
VN-Matrix 200 Series • Serial Transport and Control Methodsl 48
- User Guide 1
- VN-Matrix 1
- 200 Series: 1
- VNC 200 DVI, VNE 200 DVI, and 1
- VND 200 DVI 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- Copyright 3
- Trademarks 3
- Contents 4
- Introduction 6
- Firmware Version 7
- Product Range 7
- Functional Overview 8
- Decoder Display Capability 9
- Control Capability 9
- Network Requirements 9
- Example System Application 10
- Data Transport Methods 10
- SOURCE DISPLAY 11
- SOURCE DISPLA 12
- VN-MATRIX 200 SERIES 13
- RGB/DVI OVER IP 13
- Rear Panel Features 14
- Installation 15
- Procedure 15
- Mounting Requirements 16
- Power Connection via PSU 17
- Power Cord for PSU 18
- External Supply Protection 19
- Network Communications Setup 20
- To access the setup menus… 21
- Connect Devices 24
- Connecting a digital source 25
- SOURCE COMPUTER 26
- Connecting a digital display 27
- Connecting an analog display 28
- Device List Page 31
- Save All tab 32
- Additional Setup for Audio 35
- EDID options 36
- Identify Mode 36
- Audio status 37
- Advanced setup options 38
- Help tab for details 39
- Help tab 39
- Save All tab as shown above 40
- Identify mode 41
- Nodata Splash Mode 43
- Device mode 44
- Troubleshooting 45
- Source Checkup 47
- System Checkup 48
- Controller Checkup 49
- Serial Transport 50
- TCP RS-232RS-232 TCP 51
- Serial / Telnet Commands 52
- Device Commands 53
- Data Stream Mode 54
- Remote Keyboard 56
- Operation 56
- Mouse and Keyboard Control 57
- Mode = Enable 59
- Advanced Setup 60
- Procedures 60
- Video Setup Page 61
- Custom Input Modes 63
- Configure tab 64
- Creating a custom input mode 65
- VideoPort icon b 67
- Video Setup tab c 67
- Bandwidth (Source) Page 69
- Figure 45. Bandwidth Page 70
- Bandwidth Management 71
- Setting the maximum bit rate 72
- Setting the video quality 72
- Transform setting 73
- Quality Control settings 74
- Temporal compression setting 74
- Monitoring the bit rate 75
- Audio Compression 76
- Decoder Set Up 77
- Adjusting the Playback Delay 79
- Custom Output Modes 80
- Creating a CVT output mode 81
- Creating a custom output mode 81
- Parameter Meaning 82
- Controller Configuration 84
- Controller Licensing 85
- Upgrading Device Firmware 85
- Changing a Device Licence 88
- Update Licence button 89
- Alarms and SNMP 90
- Alarms Page 91
- Apply Filter Change 92
- Save All tab is used to make 92
- Alarms tab is selected 92
- Alarm Logs 93
- Overview – SNMP 96
- SNMP Trap Destinations 97
- IP Addressing 98
- Choosing IP Addresses 99
- Subnet Mask 100
- Response Messages 100
- Understanding 102
- Network 102
- Performance 102
- Nodes, Switchers, and Routers 103
- Protocols 103
- Browser 106
- Configuration 106
- To enable JavaScript: 107
- Mozilla (v1.3 or Above) 108
- Technical Data 110
- DVI Input (IN) 111
- DVI Output (OUT/LOOP) 113
- Network (1 and 2) 115
- RS-232 Port Settings 116
- Serial Port Login Procedure 117
- Command options 117
- Starting Telnet 118
- Login Procedure 118
- Reference 119
- Information 119
- Accessories 122
- Extron® Warranty 123
- Warranty 123
Related products and manuals for Accessories for video Extron-electronics VN-Matrix 200 Series
(138 pages)© 2020, manymanuals.com. All rights reserved. | 1.192 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals