Extron-electronics ISM 482 User Manual Page 16
- Page / 82
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ISM 482 Integrated Scaling Matrix Switcher • Installation 10
Wiring the network cable
The cable can be terminated as either a patch cable or a crossover cable (see figure 9) and
must be properly terminated for your application:
• Patch (straight) cable — Connection of the ISM to an Ethernet hub, router, or
switcher that also hosts a controlling computer
• Crossover cable — Direct connection between the ISM and a controlling computer
A cable that is wired as T568A at one end
and T568B at the other (Tx and Rx pairs
reversed) is a "crossover" cable.
A cable that is wired the same at both ends is
called a "straight-through" cable, because
no pin/pair assignments are swapped.
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
Crossover Cable Straight-through Cable
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
End 1 End 2 End 1 End 2
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Pin
1
2
3
4
5
6
7
8
Wire color
White-orange
White-green
Blue
White-blue
White-brown
Brown
Wire color
T568BT568B
White-orange
OrangeOrange
White-green
Blue
White-blue
GreenGreen
White-brown
Brown
Figure 9. RJ-45 Connector Pinout Tables
RS-232 Connection
h Remote port — Connect a host device, such as a computer or touch panel control,
to the integration scaling matrix switcher via this 9-pin D connector for serial RS-232
control (see figure 10).
RS-232 FunctionPin
1
2
3
4
5
6
7
8
9
—
TX
RX
—
Gnd
—
—
—
—
Not used
Transmit data
Receive data
Not used
Signal ground
Not used
Not used
Not used
Not used
51
9
5
9
6
Female
Male
1
6
Figure 10. Remote Port Pin Assignments
See Programming Guide on page 31, for definitions of the SIS commands and
Switcher Software on page 47, to install and use the control software.
Configuration
The ISM can be configured using either the front panel controls, the SIS, or the Windows
Control program (see the Operation section on page 16, the Programming Guide section
on page 38, the Switcher Software section on page 49, and the HTML Operation
section on page 60
- User Guide 1
- No Photo 1
- Available yet 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 3
- Software Commands 4
- Contents 5
- Introduction 7
- Network/ 8
- Internet 8
- Features 9
- Installation 11
- Input Connections 12
- RCA Connector 13
- 3.5 mm Stereo Plug Connector 13
- Standard Output Connections 14
- Ethernet Connection 15
- Optional Output Connection 15
- Configuration 16
- Operation 17
- Output Buttons and LEDs 18
- Selecting an input 19
- Recalling a user preset 19
- Black/Mute Button and LEDs 20
- Picture Adjustment Buttons 20
- Front Panel Operations 21
- Menu System Overview 22
- Input Configuration submenu 23
- Output Configuration menu 24
- Output Resolution submenu 24
- Advanced Configuration Menu 26
- Test Pattern submenu 27
- Blanking submenu 27
- RGB Delay submenu 27
- Enhanced Mode submenu 28
- Pixel Phase submenu 28
- PAL Film Mode submenu 28
- Reset submenu 28
- User Presets menu 29
- Save Preset submenu 29
- Erase Preset submenu 30
- Exit menu 30
- Picture Adjustments 31
- Press and hold both buttons 32
- IP Information 33
- Optimizing the Video 34
- Optimizing the Audio 35
- Troubleshooting 35
- General Checks 36
- Specific Problems 36
- Programming Guide 37
- Ethernet Link 38
- } character) 39
- Switcher-Initiated Messages 40
- Host-to-Switcher Instructions 43
- Switcher Error Responses 43
- Command Function 44
- SIS Command 44
- Response 44
- Additional description 44
- Symbol definitions 50
- Command and response table 50
- Switcher Software 53
- Ethernet protocol settings 54
- Using the Control Program 55
- Button-Label Generator 57
- Using the Software 58
- HTML Operation 59
- Control Page 61
- Freezing the Output 62
- Outputting a Test Pattern 62
- Previewing the Scan Rate 62
- Using Blue-Only Mode 62
- Executive Mode 62
- System Configuration Page 63
- ISM IP Settings Fields 64
- File Management Page 65
- I/O Configuration Page 66
- Output resolution 68
- Output rate 68
- Output format 68
- Output polarity 69
- Maintenance and 70
- Modifications 70
- Switcher 71
- Installing a Firmware Upgrade 72
- Installing a DVI Output Card 73
- Determining Default Addresses 76
- Connecting as a Telnet Client 77
- Reference 79
- Information 79
- Button Labels 80
- Extron Warranty 82
Related products and manuals for Accessories for video Extron-electronics ISM 482
(9 pages)© 2020, manymanuals.com. All rights reserved. | 1.292 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals