Extron-electronics ISM 482 User Manual Page 73
- Page / 82
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ISM 482 Integrated Scaling Matrix Switcher • Maintenance and Modifications 67
4. Align the slots of each new firmware chip with the angled corners of the socket in the
same orientation as the old chip. Gently, but firmly, press the chip into place in the
socket.
5. Close the switcher (see “Opening and Closing the Switcher,” starting with step 9 on
page 65).
Installing a DVI Output Card
You can install an optional digital visual interface (DVI) output card in the ISS. With the card
installed, a additional DVI video output 1 on a standard DVI connector. The DVI output is
the video tied to output 1 and is in addition to the standard output 1 RGB video on BNC
connector and 15-pin HD connectors. Extron recommends that you send the unit to Extron
for service and updates.
Install an optional DVI output card in the ISM as follows:
ATTENTION: Changes to electronic components must be performed by authorized
service personnel only.
CAUTION: Electric shock hazard. To prevent electric shock, always unplug the ISS
from the AC power source before opening the enclosure.
1. Open the switcher (see Opening and Closing the Switcher on page 64).
ATTENTION: Do not touch any switches or other electronic components inside the
ISM. Doing so could damage the ISM. Electrostatic discharge (ESD) can damage
IC chips even though you cannot feel it. You must be electrically grounded before
proceeding with any electronic component replacement. A grounding wrist strap
is recommended.
2. Locate the DVI output card connector opening on the rear panel and the DVI output
card connector J14. When viewed from the front, connector J14 is in the far left corner
of the main circuit board (see figure 51).
DVI Output Card
Connector J14 on
Main Circuit Board
DVI Output Card
Connector Opening
in ISM Rear Panel
Figure 51. DVI Output Card Connector Opening and Socket J14
3. If the rear panel DVI connector opening is still covered, remove the two screws that
secure the cover to the back panel and remove the cover.
- User Guide 1
- No Photo 1
- Available yet 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 3
- Software Commands 4
- Contents 5
- Introduction 7
- Network/ 8
- Internet 8
- Features 9
- Installation 11
- Input Connections 12
- RCA Connector 13
- 3.5 mm Stereo Plug Connector 13
- Standard Output Connections 14
- Ethernet Connection 15
- Optional Output Connection 15
- Configuration 16
- Operation 17
- Output Buttons and LEDs 18
- Selecting an input 19
- Recalling a user preset 19
- Black/Mute Button and LEDs 20
- Picture Adjustment Buttons 20
- Front Panel Operations 21
- Menu System Overview 22
- Input Configuration submenu 23
- Output Configuration menu 24
- Output Resolution submenu 24
- Advanced Configuration Menu 26
- Test Pattern submenu 27
- Blanking submenu 27
- RGB Delay submenu 27
- Enhanced Mode submenu 28
- Pixel Phase submenu 28
- PAL Film Mode submenu 28
- Reset submenu 28
- User Presets menu 29
- Save Preset submenu 29
- Erase Preset submenu 30
- Exit menu 30
- Picture Adjustments 31
- Press and hold both buttons 32
- IP Information 33
- Optimizing the Video 34
- Optimizing the Audio 35
- Troubleshooting 35
- General Checks 36
- Specific Problems 36
- Programming Guide 37
- Ethernet Link 38
- } character) 39
- Switcher-Initiated Messages 40
- Host-to-Switcher Instructions 43
- Switcher Error Responses 43
- Command Function 44
- SIS Command 44
- Response 44
- Additional description 44
- Symbol definitions 50
- Command and response table 50
- Switcher Software 53
- Ethernet protocol settings 54
- Using the Control Program 55
- Button-Label Generator 57
- Using the Software 58
- HTML Operation 59
- Control Page 61
- Freezing the Output 62
- Outputting a Test Pattern 62
- Previewing the Scan Rate 62
- Using Blue-Only Mode 62
- Executive Mode 62
- System Configuration Page 63
- ISM IP Settings Fields 64
- File Management Page 65
- I/O Configuration Page 66
- Output resolution 68
- Output rate 68
- Output format 68
- Output polarity 69
- Maintenance and 70
- Modifications 70
- Switcher 71
- Installing a Firmware Upgrade 72
- Installing a DVI Output Card 73
- Determining Default Addresses 76
- Connecting as a Telnet Client 77
- Reference 79
- Information 79
- Button Labels 80
- Extron Warranty 82
Related products and manuals for Accessories for video Extron-electronics ISM 482
(9 pages)© 2020, manymanuals.com. All rights reserved. | 0.292 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals